Time-frequency processing based method for rotor/stator rub localization
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23520%2F16%3A43929834" target="_blank" >RIV/49777513:23520/16:43929834 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.scopus.com/record/display.uri?origin=resultslist&eid=2-s2.0-85002838965" target="_blank" >https://www.scopus.com/record/display.uri?origin=resultslist&eid=2-s2.0-85002838965</a>
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Time-frequency processing based method for rotor/stator rub localization
Popis výsledku v původním jazyce
Rotor-stator rub is not very common, but hazardous state, which does not allow normal operation of the machine. The main reasons of rub occurrence are high shaft vibrations, tight clearances of the seals and thermal deformation of stator parts. The diagnostics of rub consists of two tasks. The first task is detection of rub, normally based on tracking of 1X phasor in complex domain or detection of 1X integral submultiples in signal spectrum. The second task is determination of the place, where rub occurred. This paper describes a new method of rub localization based on time-frequency processing of stator vibrations. Developed method uses standardly installed vibration sensors without need of any further equipment. The rub localization method was and tested during experiments on rotor stand and then used in operation of steam turbine. The accuracy of proposed method was verified after an inspection during the steam turbine outage.
Název v anglickém jazyce
Time-frequency processing based method for rotor/stator rub localization
Popis výsledku anglicky
Rotor-stator rub is not very common, but hazardous state, which does not allow normal operation of the machine. The main reasons of rub occurrence are high shaft vibrations, tight clearances of the seals and thermal deformation of stator parts. The diagnostics of rub consists of two tasks. The first task is detection of rub, normally based on tracking of 1X phasor in complex domain or detection of 1X integral submultiples in signal spectrum. The second task is determination of the place, where rub occurred. This paper describes a new method of rub localization based on time-frequency processing of stator vibrations. Developed method uses standardly installed vibration sensors without need of any further equipment. The rub localization method was and tested during experiments on rotor stand and then used in operation of steam turbine. The accuracy of proposed method was verified after an inspection during the steam turbine outage.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20205 - Automation and control systems
Návaznosti výsledku
Projekt
<a href="/cs/project/LO1506" target="_blank" >LO1506: Podpora udržitelnosti centra NTIS - Nové technologie pro informační společnost</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2016
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
The Thirteenth International Conference on Condition Monitoring and Machinery Failure Prevention Technologies CM2016 / MFPT2016
ISBN
978-1-5108-3093-6
ISSN
—
e-ISSN
neuvedeno
Počet stran výsledku
11
Strana od-do
1-11
Název nakladatele
The British Institute for Non-Destructive Testing
Místo vydání
Northampton
Místo konání akce
Novotel Paris Sud Charenton, Paříž, Francie
Datum konání akce
10. 10. 2016
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
—