Non-contact charge temperature measurement on industrial continuous furnaces and steel charge emissivity analysis
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23640%2F13%3A43918874" target="_blank" >RIV/49777513:23640/13:43918874 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.1016/j.infrared.2013.07.005" target="_blank" >http://dx.doi.org/10.1016/j.infrared.2013.07.005</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.infrared.2013.07.005" target="_blank" >10.1016/j.infrared.2013.07.005</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Non-contact charge temperature measurement on industrial continuous furnaces and steel charge emissivity analysis
Popis výsledku v původním jazyce
Continuous furnaces are commonly used for steel billet reheating before a rolling operation. It is necessary to perform a number of measurements to set-up and operate the optimization system of the furnaces correctly. A charge temperature measurement using infrared detectors can be one of the usable measurement techniques. This non-contact measurement method is based on the detection of infrared radiation emitted from a measured surface. The radiation intensity depends on the surface temperature and emissivity, which is one of the most important parameters for infrared measurements. Advantages of the non-contact temperature measurement, as well as some problems regarding the surface emissivity, are presented. The direct steel billet temperature measurement procedure using infra-red detectors, emissivity determination procedures, and example results are introduced. It is shown that steel emissivity can vary from approx. 0.17 to 0.8, depending on the surface state, scale formation, and w
Název v anglickém jazyce
Non-contact charge temperature measurement on industrial continuous furnaces and steel charge emissivity analysis
Popis výsledku anglicky
Continuous furnaces are commonly used for steel billet reheating before a rolling operation. It is necessary to perform a number of measurements to set-up and operate the optimization system of the furnaces correctly. A charge temperature measurement using infrared detectors can be one of the usable measurement techniques. This non-contact measurement method is based on the detection of infrared radiation emitted from a measured surface. The radiation intensity depends on the surface temperature and emissivity, which is one of the most important parameters for infrared measurements. Advantages of the non-contact temperature measurement, as well as some problems regarding the surface emissivity, are presented. The direct steel billet temperature measurement procedure using infra-red detectors, emissivity determination procedures, and example results are introduced. It is shown that steel emissivity can vary from approx. 0.17 to 0.8, depending on the surface state, scale formation, and w
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JB - Senzory, čidla, měření a regulace
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/ED2.1.00%2F03.0088" target="_blank" >ED2.1.00/03.0088: Centrum nových technologií a materiálů (CENTEM)</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2013
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
INFRARED PHYSICS & TECHNOLOGY
ISSN
1350-4495
e-ISSN
—
Svazek periodika
61
Číslo periodika v rámci svazku
November
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
7
Strana od-do
20-26
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—