A novel approach to polyaluminosialates curing process using electric boosting and temperature profile investigation by DSC
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23640%2F15%3A43925669" target="_blank" >RIV/49777513:23640/15:43925669 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.1007/s10973-015-4643-8" target="_blank" >http://dx.doi.org/10.1007/s10973-015-4643-8</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1007/s10973-015-4643-8" target="_blank" >10.1007/s10973-015-4643-8</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
A novel approach to polyaluminosialates curing process using electric boosting and temperature profile investigation by DSC
Popis výsledku v původním jazyce
The curing procedures of polyaluminosialates mixtures at elevated temperature are widely involved in preparation of geopolymer systems. This paper deals with design and characterization of a novel curing process by electric boosting where electric power,current and voltage were controlled in relation to the curing temperature of geopolymer binder based on concentrated potassium silicate solution. Two types of specimens were prepared, namely beam-shaped specimens with a volume of 96 cm3 to study the flexural strength and apparent porosity development and plates with a volume of 352 cm3 to investigate changes of electric parameters in relation to the elevated temperature during the curing process in an increased volume specimens. The evolution of curingtemperature was controlled by manually adjusting the electric power, depending on the specimen type, so as not to exceed 80 oC. An analysis of the curing mechanism is presented for highly filled geopolymer paste with angular particles of
Název v anglickém jazyce
A novel approach to polyaluminosialates curing process using electric boosting and temperature profile investigation by DSC
Popis výsledku anglicky
The curing procedures of polyaluminosialates mixtures at elevated temperature are widely involved in preparation of geopolymer systems. This paper deals with design and characterization of a novel curing process by electric boosting where electric power,current and voltage were controlled in relation to the curing temperature of geopolymer binder based on concentrated potassium silicate solution. Two types of specimens were prepared, namely beam-shaped specimens with a volume of 96 cm3 to study the flexural strength and apparent porosity development and plates with a volume of 352 cm3 to investigate changes of electric parameters in relation to the elevated temperature during the curing process in an increased volume specimens. The evolution of curingtemperature was controlled by manually adjusting the electric power, depending on the specimen type, so as not to exceed 80 oC. An analysis of the curing mechanism is presented for highly filled geopolymer paste with angular particles of
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
CA - Anorganická chemie
OECD FORD obor
—
Návaznosti výsledku
Projekt
Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2015
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Journal of Thermal Analysis and Calorimetry
ISSN
1388-6150
e-ISSN
—
Svazek periodika
121
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
NL - Nizozemsko
Počet stran výsledku
8
Strana od-do
517-524
Kód UT WoS článku
000356455000060
EID výsledku v databázi Scopus
—