Use of 3D Printing for Horn Antenna Manufacturing

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60162694%3AG43__%2F23%3A00558011" target="_blank" >RIV/60162694:G43__/23:00558011 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216305:26220/22:PU144467

Výsledek na webu

<a href="https://www.mdpi.com/2079-9292/11/10/1539" target="_blank" >https://www.mdpi.com/2079-9292/11/10/1539</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/electronics11101539" target="_blank" >10.3390/electronics11101539</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Use of 3D Printing for Horn Antenna Manufacturing

Popis výsledku v původním jazyce

This article describes the manufacturing of a horn antenna using a 3D commercial printer. The horn antenna was chosen for its simplicity and practical versatility. The standardised horn antenna is one of the most widely used antennas in microwave technology. A standardised horn antenna can be connected to standardised waveguides. The horn antenna has been selected so that this antenna can be fabricated by 3D printing and thus obtain the equivalent of a standardised horn antenna. This 3D horn antenna can then be excited by a standardised waveguide. The 3Dprinted horn antenna with metallic layers has very good impedance characteristics, standing wave ratio and radiation patterns that are close to those of a standardised horn antenna. The 3D-based horn antenna is suitable for applications where low antenna weight is required, such as aerospace and satellite technologies. The article also describes a manufacturing procedure for a horn antenna (E-sector horn antenna) that is plated with galvanic layers of silver and gold. The design of the plated horn antenna in the Matlab application using the Antenna Toolbox extension is also described, including 3D printing procedures, post-processing procedures (plating) and practical testing of its functionality. The measured results are compared to simulations of the standardised horn antenna and then analysed.

Název v anglickém jazyce

Use of 3D Printing for Horn Antenna Manufacturing

Popis výsledku anglicky

This article describes the manufacturing of a horn antenna using a 3D commercial printer. The horn antenna was chosen for its simplicity and practical versatility. The standardised horn antenna is one of the most widely used antennas in microwave technology. A standardised horn antenna can be connected to standardised waveguides. The horn antenna has been selected so that this antenna can be fabricated by 3D printing and thus obtain the equivalent of a standardised horn antenna. This 3D horn antenna can then be excited by a standardised waveguide. The 3Dprinted horn antenna with metallic layers has very good impedance characteristics, standing wave ratio and radiation patterns that are close to those of a standardised horn antenna. The 3D-based horn antenna is suitable for applications where low antenna weight is required, such as aerospace and satellite technologies. The article also describes a manufacturing procedure for a horn antenna (E-sector horn antenna) that is plated with galvanic layers of silver and gold. The design of the plated horn antenna in the Matlab application using the Antenna Toolbox extension is also described, including 3D printing procedures, post-processing procedures (plating) and practical testing of its functionality. The measured results are compared to simulations of the standardised horn antenna and then analysed.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10201 - Computer sciences, information science, bioinformathics (hardware development to be 2.2, social aspect to be 5.8)

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

ELECTRONICS

ISSN

2079-9292

e-ISSN

2079-9292

Svazek periodika

11

Číslo periodika v rámci svazku

10

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

15

Strana od-do

1539

Kód UT WoS článku

000803228300001

EID výsledku v databázi Scopus

2-s2.0-85129750838