Effects of aluminium microparticles and surface treatment of AlCu4Mg on mechanical properties of adhesive bond strength

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F17%3A73307" target="_blank" >RIV/60460709:41310/17:73307 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Effects of aluminium microparticles and surface treatment of AlCu4Mg on mechanical properties of adhesive bond strength

Popis výsledku v původním jazyce

The aim of the research was to evaluate the lapping length, the adhesive bonded surface treatment and the influence of the filler in the form of the aluminium microparticles on the adhesive bond strength. The alloy AlCu4Mg was the adhesive bonded material bonded by means of a two-component epoxy adhesive used in construction of machines. The filler in a form of aluminium microparticles was added into the adhesive. Laboratory experiments were performed on normalized testing samples of alloy AlCu4Mg prepared under standard ČSN EN 1465. Within the research three various treatments of the adhesive bonded surface were evaluated, i.e. without the surface treatment (WT), mechanical treatment of the surface (MT) and mechanical and chemical treatment of the surface (MCHT). The adhesive bonds without the adhesive bonded surface treatment (marked as WT) reach the smallest adhesive bond strength. When adding the filler in the form of aluminium microparticles (10 vol. %) the adhesive bond strength was increased o

Název v anglickém jazyce

Effects of aluminium microparticles and surface treatment of AlCu4Mg on mechanical properties of adhesive bond strength

Popis výsledku anglicky

The aim of the research was to evaluate the lapping length, the adhesive bonded surface treatment and the influence of the filler in the form of the aluminium microparticles on the adhesive bond strength. The alloy AlCu4Mg was the adhesive bonded material bonded by means of a two-component epoxy adhesive used in construction of machines. The filler in a form of aluminium microparticles was added into the adhesive. Laboratory experiments were performed on normalized testing samples of alloy AlCu4Mg prepared under standard ČSN EN 1465. Within the research three various treatments of the adhesive bonded surface were evaluated, i.e. without the surface treatment (WT), mechanical treatment of the surface (MT) and mechanical and chemical treatment of the surface (MCHT). The adhesive bonds without the adhesive bonded surface treatment (marked as WT) reach the smallest adhesive bond strength. When adding the filler in the form of aluminium microparticles (10 vol. %) the adhesive bond strength was increased o

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20505 - Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics; filled composites)

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

17

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

66-71

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85013805113