3D Woven Textile Structural Polymer Composites: Effect of Resin Processing Parameters on Mechanical Performance

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F22%3A96659" target="_blank" >RIV/60460709:41310/22:96659 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/46747885:24210/22:00009557 RIV/46747885:24620/22:00009557

Výsledek na webu

<a href="https://doi.org/10.3390/polym14061134" target="_blank" >https://doi.org/10.3390/polym14061134</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/polym14061134" target="_blank" >10.3390/polym14061134</a>

Jazyk výsledku

angličtina

Název v původním jazyce

3D Woven Textile Structural Polymer Composites: Effect of Resin Processing Parameters on Mechanical Performance

Popis výsledku v původním jazyce

This work presents the manufacture of polymer composites using 3D woven structures (orthogonal, angle interlock and warp interlock) with glass multifilament tows and epoxy as the resin. The mechanical properties were analyzed by varying the processing parameters, namely, add-on percentage, amount of hardener, curing time, curing temperature and molding pressure, at four different levels during the composite fabrication for three different 3D woven structures. The mechanical properties of composites are affected by resin infusion or resin impregnation. Resin infusion depends on many processing conditions (temperature, pressure, viscosity and molding time), the structure of the reinforcement and the compatibility of the resin with the reinforcement. The samples were tested for tensile strength, tensile modulus, impact resistance and flexural strength. Optimal process parameters were identified for different 3D-woven-structure-based composites for obtaining optimal results for tensile strength, tensile modulus, impact resistance and flexural strength. The tensile strength, elongation at break and tensile modulus were found to be at a maximum for the angle interlock structure among the various 3D woven composites. A composition of 55% matrix (including 12% of hardener added) and 45% fiber were found to be optimal for the tensile and impact performance of 3D woven glass-epoxy composites. A curing temperature of about 140 degrees C seemed to be optimal for glass-epoxy composites. Increasing the molding pressure up to 12 bar helped with better penetration of the resin, resulting in higher tensile strength, modulus and impact performance. The optimal conditions for the best flexural performance in 3D woven glass-epoxy composites were 12% hardener, 140 degrees C curing temperature, 900 s curing time and 12 bar molding pressure.

Název v anglickém jazyce

3D Woven Textile Structural Polymer Composites: Effect of Resin Processing Parameters on Mechanical Performance

Popis výsledku anglicky

This work presents the manufacture of polymer composites using 3D woven structures (orthogonal, angle interlock and warp interlock) with glass multifilament tows and epoxy as the resin. The mechanical properties were analyzed by varying the processing parameters, namely, add-on percentage, amount of hardener, curing time, curing temperature and molding pressure, at four different levels during the composite fabrication for three different 3D woven structures. The mechanical properties of composites are affected by resin infusion or resin impregnation. Resin infusion depends on many processing conditions (temperature, pressure, viscosity and molding time), the structure of the reinforcement and the compatibility of the resin with the reinforcement. The samples were tested for tensile strength, tensile modulus, impact resistance and flexural strength. Optimal process parameters were identified for different 3D-woven-structure-based composites for obtaining optimal results for tensile strength, tensile modulus, impact resistance and flexural strength. The tensile strength, elongation at break and tensile modulus were found to be at a maximum for the angle interlock structure among the various 3D woven composites. A composition of 55% matrix (including 12% of hardener added) and 45% fiber were found to be optimal for the tensile and impact performance of 3D woven glass-epoxy composites. A curing temperature of about 140 degrees C seemed to be optimal for glass-epoxy composites. Increasing the molding pressure up to 12 bar helped with better penetration of the resin, resulting in higher tensile strength, modulus and impact performance. The optimal conditions for the best flexural performance in 3D woven glass-epoxy composites were 12% hardener, 140 degrees C curing temperature, 900 s curing time and 12 bar molding pressure.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

POLYMERS

ISSN

2073-4360

e-ISSN

2073-4360

Svazek periodika

14

Číslo periodika v rámci svazku

MAR 2022

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

25

Strana od-do

—

Kód UT WoS článku

000776428000001

EID výsledku v databázi Scopus

2-s2.0-85126935533