Tribological Behaviour of Enamel Coatings Created by a Prototype Device for Local Repair of Inorganic Surfaces

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41310%2F23%3A94560" target="_blank" >RIV/60460709:41310/23:94560 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/46747885:24210/23:00011660

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/16/3/1224" target="_blank" >https://www.mdpi.com/1996-1944/16/3/1224</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma16031224" target="_blank" >10.3390/ma16031224</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Tribological Behaviour of Enamel Coatings Created by a Prototype Device for Local Repair of Inorganic Surfaces

Popis výsledku v původním jazyce

The ability of materials to withstand environmental influences is a frequent necessity in many industries. Special requirements are imposed by such industries where surfaces are affected by acidity during the processing or storage of products. In such cases, when the basic surface is exposed to chemical influences, it is possible to use enamel coatings, which, with their properties, guarantee the protection of the surface and achieve the required service life of the material. This article deals mainly with the interaction between the base material and the enamel and its resistance to wear between the original and the renovated surface caused by local heating. The article presents a methodical procedure for the preparation of test specimens with an enamel layer prepared by AWJ cutting, eliminating its damage. There are minimal differences in the microstructure between the original and the renovated surface due to the production technique. The renovated enamel surface had more bubbles of a larger size than the original surface. Good adhesion between the base metal material (substrate) and the ground coat was demonstrated. The tested surfaces demonstrated high resistance to intensive abrasion conditions with low linear wear increments.

Název v anglickém jazyce

Tribological Behaviour of Enamel Coatings Created by a Prototype Device for Local Repair of Inorganic Surfaces

Popis výsledku anglicky

The ability of materials to withstand environmental influences is a frequent necessity in many industries. Special requirements are imposed by such industries where surfaces are affected by acidity during the processing or storage of products. In such cases, when the basic surface is exposed to chemical influences, it is possible to use enamel coatings, which, with their properties, guarantee the protection of the surface and achieve the required service life of the material. This article deals mainly with the interaction between the base material and the enamel and its resistance to wear between the original and the renovated surface caused by local heating. The article presents a methodical procedure for the preparation of test specimens with an enamel layer prepared by AWJ cutting, eliminating its damage. There are minimal differences in the microstructure between the original and the renovated surface due to the production technique. The renovated enamel surface had more bubbles of a larger size than the original surface. Good adhesion between the base metal material (substrate) and the ground coat was demonstrated. The tested surfaces demonstrated high resistance to intensive abrasion conditions with low linear wear increments.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/FV40144" target="_blank" >FV40144: Návrh a výroba prototypu zařízení pro lokální opravy funkčnosti anorganických povrchů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

1996-1944

Svazek periodika

16

Číslo periodika v rámci svazku

3

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

14

Strana od-do

—

Kód UT WoS článku

000929642200001

EID výsledku v databázi Scopus

2-s2.0-85148008005