Stiffness coefficients of mortise and tenon joints used on wooden window profiles
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F16%3A72294" target="_blank" >RIV/60460709:41320/16:72294 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.15376/biores.11.2.4677-4687" target="_blank" >http://dx.doi.org/10.15376/biores.11.2.4677-4687</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.15376/biores.11.2.4677-4687" target="_blank" >10.15376/biores.11.2.4677-4687</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Stiffness coefficients of mortise and tenon joints used on wooden window profiles
Popis výsledku v původním jazyce
Samples of corner joints of wooden rectangular windows, with widths of 78 and 92 mm, were used to determine the stiffness of tenon and mortise joints. Two series of samples were loaded statically in the angular plane of compression and tension, so that the bending moment could be derived. The objective of the experiment was to determine the existing correlations between the stiffness in maximum strength and the stiffness in the elastic area for both types of tests. After strength tests were carried out, the annual ring width of the samples was measured to determine whether this factor affects the stiffness of the joints. The results showed that there was a relatively strong correlation between the stiffness in the elastic area and the maximum load. A two-factor analysis of variance confirmed that the type of load did not affect the stiffness of the joint, but the type of joint (width) does significantly affect the stiffness. Therefore, the width of annual rings was positively correlated with the stif
Název v anglickém jazyce
Stiffness coefficients of mortise and tenon joints used on wooden window profiles
Popis výsledku anglicky
Samples of corner joints of wooden rectangular windows, with widths of 78 and 92 mm, were used to determine the stiffness of tenon and mortise joints. Two series of samples were loaded statically in the angular plane of compression and tension, so that the bending moment could be derived. The objective of the experiment was to determine the existing correlations between the stiffness in maximum strength and the stiffness in the elastic area for both types of tests. After strength tests were carried out, the annual ring width of the samples was measured to determine whether this factor affects the stiffness of the joints. The results showed that there was a relatively strong correlation between the stiffness in the elastic area and the maximum load. A two-factor analysis of variance confirmed that the type of load did not affect the stiffness of the joint, but the type of joint (width) does significantly affect the stiffness. Therefore, the width of annual rings was positively correlated with the stif
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JJ - Ostatní materiály
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2016
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
BioResources
ISSN
1930-2126
e-ISSN
—
Svazek periodika
11
Číslo periodika v rámci svazku
2
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
11
Strana od-do
4677-4687
Kód UT WoS článku
000375786700125
EID výsledku v databázi Scopus
—