Bendability characteristics of wood lamellae in plastic region
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60460709%3A41320%2F17%3A72274" target="_blank" >RIV/60460709:41320/17:72274 - isvavai.cz</a>
Výsledek na webu
<a href="http://dx.doi.org/10.1016/j.compstruct.2016.12.052" target="_blank" >http://dx.doi.org/10.1016/j.compstruct.2016.12.052</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.compstruct.2016.12.052" target="_blank" >10.1016/j.compstruct.2016.12.052</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Bendability characteristics of wood lamellae in plastic region
Popis výsledku v původním jazyce
This article examines the effect of different factors (material thickness, degree of densification and number of loading cycles) on the selected bending characteristics of European beech (Fagus sylvatica L.) and European aspen (Populus tremula L.). The bending characteristics, including bending strength, plasticity potential and modulus of plasticity, were measured using three-point bending. Results of the four-factor analysis demonstrate that each bending characteristic is affected differently by the given factors. The bending strength, which was higher in beech wood than in aspen wood, increased along with the degree of densification. Cyclic loading had no significant effect on the bending strength. Although material thickness had some statistical significance, its effect was not unequivocal. The modulus of plasticity was significantly affected only by the wood species and material thickness. Higher modulus of plasticity values were achieved in beech wood than in aspen wood. The modulus of plastic
Název v anglickém jazyce
Bendability characteristics of wood lamellae in plastic region
Popis výsledku anglicky
This article examines the effect of different factors (material thickness, degree of densification and number of loading cycles) on the selected bending characteristics of European beech (Fagus sylvatica L.) and European aspen (Populus tremula L.). The bending characteristics, including bending strength, plasticity potential and modulus of plasticity, were measured using three-point bending. Results of the four-factor analysis demonstrate that each bending characteristic is affected differently by the given factors. The bending strength, which was higher in beech wood than in aspen wood, increased along with the degree of densification. Cyclic loading had no significant effect on the bending strength. Although material thickness had some statistical significance, its effect was not unequivocal. The modulus of plasticity was significantly affected only by the wood species and material thickness. Higher modulus of plasticity values were achieved in beech wood than in aspen wood. The modulus of plastic
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20502 - Paper and wood
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2017
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
COMPOSITE STRUCTURES
ISSN
0263-8223
e-ISSN
—
Svazek periodika
163
Číslo periodika v rámci svazku
MAR
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
13
Strana od-do
410-422
Kód UT WoS článku
000393931800033
EID výsledku v databázi Scopus
2-s2.0-85007278590