Corrosion properties of AlSi10Mg alloy prepared by gravity die casting and 3D printing technology
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60461373%3A22310%2F17%3A43915355" target="_blank" >RIV/60461373:22310/17:43915355 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Corrosion properties of AlSi10Mg alloy prepared by gravity die casting and 3D printing technology
Popis výsledku v původním jazyce
Aluminium and its alloys are widely used in the transport industry. In combination with 3D printing technology, lightweight parts can be successfully achieved. 3D-printing of AlSi10Mg alloy is already well-managed. However, corrosion behaviour of such 3D-printed material has not been intensely studied yet. This paper is thus focused on a primary determination of corrosion properties of AlSi10Mg samples prepared by SLM technology and on comparison with conventionally gravity cast samples in thermally untreated and treated state (T6). Audi immersion test has revealed the 3D-printed samples are the most vulnerable to local corrosion attack, while the as-cast samples are the most resistant. In all three material states, selective dissolution occurred as result of microgalvanic processes between silicon particles and aluminium matrix. Eutectics and a-Al solid solution in between the intercellular network were attacked preferentially in the cast and 3D-printed samples, respectively.
Název v anglickém jazyce
Corrosion properties of AlSi10Mg alloy prepared by gravity die casting and 3D printing technology
Popis výsledku anglicky
Aluminium and its alloys are widely used in the transport industry. In combination with 3D printing technology, lightweight parts can be successfully achieved. 3D-printing of AlSi10Mg alloy is already well-managed. However, corrosion behaviour of such 3D-printed material has not been intensely studied yet. This paper is thus focused on a primary determination of corrosion properties of AlSi10Mg samples prepared by SLM technology and on comparison with conventionally gravity cast samples in thermally untreated and treated state (T6). Audi immersion test has revealed the 3D-printed samples are the most vulnerable to local corrosion attack, while the as-cast samples are the most resistant. In all three material states, selective dissolution occurred as result of microgalvanic processes between silicon particles and aluminium matrix. Eutectics and a-Al solid solution in between the intercellular network were attacked preferentially in the cast and 3D-printed samples, respectively.
Klasifikace
Druh
J<sub>ost</sub> - Ostatní články v recenzovaných periodicích
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/GBP108%2F12%2FG043" target="_blank" >GBP108/12/G043: Mikro- a nanokrystalické materiály s vysokým podílem rozhraní pro moderní strukturní aplikace, biodegradabilní implantáty a uchovávání vodíku</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2017
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
—
Svazek periodika
17
Číslo periodika v rámci svazku
6
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
7
Strana od-do
847-853
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—