Influence of Cooling Speed during Melt Spinning Process on Properties of Al-Fe-Mm-Si-Mg Bulk Materials Prepared by SPS

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F60461373%3A22310%2F19%3A43919300" target="_blank" >RIV/60461373:22310/19:43919300 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/60461373:22810/19:43919300

Výsledek na webu

<a href="https://www.researchgate.net/publication/336919464_Influence_of_Cooling_Speed_during_Melt_Spinning_Process_on_Properties_of_Al-Fe-Mm-Si-Mg_Bulk_Materials_Prepared_by_SPS" target="_blank" >https://www.researchgate.net/publication/336919464_Influence_of_Cooling_Speed_during_Melt_Spinning_Process_on_Properties_of_Al-Fe-Mm-Si-Mg_Bulk_Materials_Prepared_by_SPS</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/367.2019/a/1213-2489/MT/19/5/813" target="_blank" >10.21062/ujep/367.2019/a/1213-2489/MT/19/5/813</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of Cooling Speed during Melt Spinning Process on Properties of Al-Fe-Mm-Si-Mg Bulk Materials Prepared by SPS

Popis výsledku v původním jazyce

This work is devoted to description of microstructure of bulk Al-Fe-Mm-Si-Mg alloys and their thermal stability. The alloy was prepared at different cooling rates (600, 1000 and 1400 RPM) during melt spinning process and sintered at the same conditions by SPS. The aim of this work was to prove if change in melt spinning conditions influence the behaviour of bulk material. It was proven that independently on cooling rate precipitation occurs during sintering process. All materials exhibited heterogenous microstructure composed of fine and coarse areas-residue of melt spinning process. During annealing of bulk materials prepared by powder metallurgy, no precipitation of new phase was observed. It is an evidence that precipitation mechanism of self-healing is not possible for these alloys.

Název v anglickém jazyce

Influence of Cooling Speed during Melt Spinning Process on Properties of Al-Fe-Mm-Si-Mg Bulk Materials Prepared by SPS

Popis výsledku anglicky

This work is devoted to description of microstructure of bulk Al-Fe-Mm-Si-Mg alloys and their thermal stability. The alloy was prepared at different cooling rates (600, 1000 and 1400 RPM) during melt spinning process and sintered at the same conditions by SPS. The aim of this work was to prove if change in melt spinning conditions influence the behaviour of bulk material. It was proven that independently on cooling rate precipitation occurs during sintering process. All materials exhibited heterogenous microstructure composed of fine and coarse areas-residue of melt spinning process. During annealing of bulk materials prepared by powder metallurgy, no precipitation of new phase was observed. It is an evidence that precipitation mechanism of self-healing is not possible for these alloys.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/GJ17-25618Y" target="_blank" >GJ17-25618Y: Příprava inovativních slitin hliníku se "self-healing" a "self-reporting" vlastnostmi</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

19

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

4

Strana od-do

813-816

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85077144329