Correlation of Magnetic Properties and Residual Stress Distribution Monitored by X-Ray and Neutron Diffraction in Welded AISI 1008 Steel Sheets

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389005%3A_____%2F15%3A00442912" target="_blank" >RIV/61389005:_____/15:00442912 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.1109/TMAG.2014.2357840" target="_blank" >http://dx.doi.org/10.1109/TMAG.2014.2357840</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1109/TMAG.2014.2357840" target="_blank" >10.1109/TMAG.2014.2357840</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Correlation of Magnetic Properties and Residual Stress Distribution Monitored by X-Ray and Neutron Diffraction in Welded AISI 1008 Steel Sheets

Popis výsledku v původním jazyce

In this paper, two identical American Iron and Steel Institute 1008 steels sheets were welded together in a butt joint configuration, with the welding line direction parallel to the rolling direction. The sheets were welded using the electron-beam welding technique. Stress distribution was monitored in the surface and the bulk of the welded samples using X-ray Bragg-Brentano and neutron diffraction methods, respectively. Accordingly, surface and bulk magnetic properties, namely magnetic Barkhausen noiseand quasi-dc permeability, were monitored in the same area. Both surface and bulk magnetic measurements exhibit good agreement with the surface and bulk stress measurements obtained by the diffraction methods, after a proper calibration procedure. Complementary measurements with scanning electron microscopy and Vicker's microhardness tester provide similar good agreement between the microstructural characterization and the residual stress distribution.

Název v anglickém jazyce

Correlation of Magnetic Properties and Residual Stress Distribution Monitored by X-Ray and Neutron Diffraction in Welded AISI 1008 Steel Sheets

Popis výsledku anglicky

In this paper, two identical American Iron and Steel Institute 1008 steels sheets were welded together in a butt joint configuration, with the welding line direction parallel to the rolling direction. The sheets were welded using the electron-beam welding technique. Stress distribution was monitored in the surface and the bulk of the welded samples using X-ray Bragg-Brentano and neutron diffraction methods, respectively. Accordingly, surface and bulk magnetic properties, namely magnetic Barkhausen noiseand quasi-dc permeability, were monitored in the same area. Both surface and bulk magnetic measurements exhibit good agreement with the surface and bulk stress measurements obtained by the diffraction methods, after a proper calibration procedure. Complementary measurements with scanning electron microscopy and Vicker's microhardness tester provide similar good agreement between the microstructural characterization and the residual stress distribution.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

BM - Fyzika pevných látek a magnetismus

OECD FORD obor

—

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

IEEE Transactions on Magnetics

ISSN

0018-9464

e-ISSN

—

Svazek periodika

51

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

4

Strana od-do

—

Kód UT WoS článku

000349446800059

EID výsledku v databázi Scopus

2-s2.0-84922743634