Texture and Differential Stress Development in W/Ni-Co Composite after Rotary Swaging

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389005%3A_____%2F20%3A00531359" target="_blank" >RIV/61389005:_____/20:00531359 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/61989100:27360/20:10245908

Výsledek na webu

<a href="https://doi.org/10.3390/ma13122869" target="_blank" >https://doi.org/10.3390/ma13122869</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma13122869" target="_blank" >10.3390/ma13122869</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Texture and Differential Stress Development in W/Ni-Co Composite after Rotary Swaging

Popis výsledku v původním jazyce

Knowledge of texture and residual stresses in tungsten heavy pseudoalloys is substantial for the microstructure optimization. These characteristics were determined in cold and warm rotary swaged W/NiCo composite with help of neutron diffraction. The results were discussed in view of the observed microstructure and mechanical properties. The investigated bars consisted of tungsten agglomerates (bcc lattice) surrounded by NiCo-based matrix (fcc lattice). No preferential crystallographic orientation was found in the as-sintered bar. A strong texture was formed in both the tungsten agglomerates ( fiber texture parallel to the swaging axis) and in the NiCo-based matrix ( fiber texture) after rotary swaging. Although usually of double-fiber texture, the fiber of the fcc structures was nearly missing in the matrix. Further, the cold-swaged bar exhibited substantially stronger texture for both phases which corresponds to the higher measured ultimate tensile strength. The residual stress differences were employed for characterization of the stress state of the bars. The largest residual stress difference (approximate to 400 MPa) was found at the center of the bar deformed at room temperature. The hoop stresses were non-symmetrical with respect to the swaging axis, which was likely caused by the elliptical cross section of the as-sintered bar.

Název v anglickém jazyce

Texture and Differential Stress Development in W/Ni-Co Composite after Rotary Swaging

Popis výsledku anglicky

Knowledge of texture and residual stresses in tungsten heavy pseudoalloys is substantial for the microstructure optimization. These characteristics were determined in cold and warm rotary swaged W/NiCo composite with help of neutron diffraction. The results were discussed in view of the observed microstructure and mechanical properties. The investigated bars consisted of tungsten agglomerates (bcc lattice) surrounded by NiCo-based matrix (fcc lattice). No preferential crystallographic orientation was found in the as-sintered bar. A strong texture was formed in both the tungsten agglomerates ( fiber texture parallel to the swaging axis) and in the NiCo-based matrix ( fiber texture) after rotary swaging. Although usually of double-fiber texture, the fiber of the fcc structures was nearly missing in the matrix. Further, the cold-swaged bar exhibited substantially stronger texture for both phases which corresponds to the higher measured ultimate tensile strength. The residual stress differences were employed for characterization of the stress state of the bars. The largest residual stress difference (approximate to 400 MPa) was found at the center of the bar deformed at room temperature. The hoop stresses were non-symmetrical with respect to the swaging axis, which was likely caused by the elliptical cross section of the as-sintered bar.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10302 - Condensed matter physics (including formerly solid state physics, supercond.)

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

—

Svazek periodika

13

Číslo periodika v rámci svazku

12

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

15

Strana od-do

2869

Kód UT WoS článku

000550195100001

EID výsledku v databázi Scopus

2-s2.0-85087444735