Keramické plazmové nástřiky bez a s dodatečnou impregnací epoxydovou pryskyřicí a jejich otěruvzdornost

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389021%3A_____%2F07%3A00087658" target="_blank" >RIV/61389021:_____/07:00087658 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Plasma sprayed ceramic coatings without and with epoxy resin sealing treatment and their wear resistance

Popis výsledku v původním jazyce

Plasma sprayed aluminum oxide-based coatings (Al2O3) are mainly used as a wear resistant surface covers in mechanical applications. Previous studies have shown that abrasion wear resistance of these coatings can be significantly improved by applying a sealing treatment. It was reported that this improvement is mainly due to microstructural toughening which takes place via the sealing process. Therefore, this study was conducted in order to determine the influence of the microstructural characteristics governed by the spray system settings and epoxy sealing on the wear resistance of these coatings. Unsealed and epoxy resin sealed plasma sprayed specimens prepared from alumina as well as alumina-13% titania were studied. Abrasion wear resistance of thesecoatings was evaluated employing the standard slurry abrasion response (SAR) and the standard dry sand rubber wheel (DSRW) abrasion tests.

Název v anglickém jazyce

Plasma sprayed ceramic coatings without and with epoxy resin sealing treatment and their wear resistance

Popis výsledku anglicky

Plasma sprayed aluminum oxide-based coatings (Al2O3) are mainly used as a wear resistant surface covers in mechanical applications. Previous studies have shown that abrasion wear resistance of these coatings can be significantly improved by applying a sealing treatment. It was reported that this improvement is mainly due to microstructural toughening which takes place via the sealing process. Therefore, this study was conducted in order to determine the influence of the microstructural characteristics governed by the spray system settings and epoxy sealing on the wear resistance of these coatings. Unsealed and epoxy resin sealed plasma sprayed specimens prepared from alumina as well as alumina-13% titania were studied. Abrasion wear resistance of thesecoatings was evaluated employing the standard slurry abrasion response (SAR) and the standard dry sand rubber wheel (DSRW) abrasion tests.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JH - Keramika, žáruvzdorné materiály a skla

OECD FORD obor

—

Projekt

<a href="/cs/project/1QS200430560" target="_blank" >1QS200430560: Progresivní žárové nástřiky odolné proti otěru</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>Z - Vyzkumny zamer (s odkazem do CEZ)

Rok uplatnění

2007

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Wear

ISSN

0043-1648

e-ISSN

—

Svazek periodika

262

Číslo periodika v rámci svazku

9-10

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

7

Strana od-do

1274-1280

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—