Benchmarking by high heat flux testing of W-steel joining technologies

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389021%3A_____%2F23%3A00579108" target="_blank" >RIV/61389021:_____/23:00579108 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.sciencedirect.com/science/article/pii/S2352179123001473?via%3Dihub" target="_blank" >https://www.sciencedirect.com/science/article/pii/S2352179123001473?via%3Dihub</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.nme.2023.101508" target="_blank" >10.1016/j.nme.2023.101508</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Benchmarking by high heat flux testing of W-steel joining technologies

Popis výsledku v původním jazyce

For a future commercial fusion reactor, the joining of tungsten and steel will be of vital importance, covering the main part of the plasma facing area. However, the large difference, of more than a factor of 2, in the coefficient of thermal expansion (CTE) of W and steel results in high thermal stresses at their interface. The cyclic nature of the operation can cause fatigue effects and could result in a premature failure of the joint. One possible solution is the insertion of a functionally graded material (FGM), with varying the CTE, as an interlayer between tungsten and steel, which could reduce these stresses. In this study, two processes, atmospheric plasma spraying (APS) and spark plasma sintering (SPS), are utilized to manufacture such FGMs. The gradation was accomplished by using two or three layers with a thickness of 0.5 mm each. Another principle is the insertion of a ductile metal interlayer, which reduces the stress by plastic deformation. Vanadium and titanium foils of varying thickness were chosen, as both have a CTE in between W and steel and V forms a solid solution with W and Fe. These and a direct W-steel joint as baseline reference were made by current-assisted diffusion bonding. All samples consist of 3 mm thick W and steel tiles allowing a direct comparison of the different technologies. An efficient high heat flux benchmark test procedure was developed and performed to investigate and compare the potential of the different joining technologies. For this, the complete stacks were brazed on actively cooled copper cooling modules and tested with high stationary heat loads of up to 5 MW/m2 with 200 cycles at each level in the JUDITH 2 facility. Detailed thermal analysis including comparison with prediction based on FEM simulation are presented to understand the cause of the failure and track the degradation. This study allows to help focusing the further development of W-steel joining technologies.

Název v anglickém jazyce

Benchmarking by high heat flux testing of W-steel joining technologies

Popis výsledku anglicky

For a future commercial fusion reactor, the joining of tungsten and steel will be of vital importance, covering the main part of the plasma facing area. However, the large difference, of more than a factor of 2, in the coefficient of thermal expansion (CTE) of W and steel results in high thermal stresses at their interface. The cyclic nature of the operation can cause fatigue effects and could result in a premature failure of the joint. One possible solution is the insertion of a functionally graded material (FGM), with varying the CTE, as an interlayer between tungsten and steel, which could reduce these stresses. In this study, two processes, atmospheric plasma spraying (APS) and spark plasma sintering (SPS), are utilized to manufacture such FGMs. The gradation was accomplished by using two or three layers with a thickness of 0.5 mm each. Another principle is the insertion of a ductile metal interlayer, which reduces the stress by plastic deformation. Vanadium and titanium foils of varying thickness were chosen, as both have a CTE in between W and steel and V forms a solid solution with W and Fe. These and a direct W-steel joint as baseline reference were made by current-assisted diffusion bonding. All samples consist of 3 mm thick W and steel tiles allowing a direct comparison of the different technologies. An efficient high heat flux benchmark test procedure was developed and performed to investigate and compare the potential of the different joining technologies. For this, the complete stacks were brazed on actively cooled copper cooling modules and tested with high stationary heat loads of up to 5 MW/m2 with 200 cycles at each level in the JUDITH 2 facility. Detailed thermal analysis including comparison with prediction based on FEM simulation are presented to understand the cause of the failure and track the degradation. This study allows to help focusing the further development of W-steel joining technologies.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Nuclear Materials and Energy

ISSN

2352-1791

e-ISSN

2352-1791

Svazek periodika

37

Číslo periodika v rámci svazku

December

Stát vydavatele periodika

NL - Nizozemsko

Počet stran výsledku

5

Strana od-do

101508

Kód UT WoS článku

001081513700001

EID výsledku v databázi Scopus

2-s2.0-85171330020