Static behavior of the weld in the joint of the steel support element using experiment and numerical modeling

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27120%2F18%3A10240639" target="_blank" >RIV/61989100:27120/18:10240639 - isvavai.cz</a>

Výsledek na webu

<a href="https://iopscience.iop.org/article/10.1088/1755-1315/143/1/012004/pdf" target="_blank" >https://iopscience.iop.org/article/10.1088/1755-1315/143/1/012004/pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/1755-1315/143/1/012004" target="_blank" >10.1088/1755-1315/143/1/012004</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Static behavior of the weld in the joint of the steel support element using experiment and numerical modeling

Popis výsledku v původním jazyce

The paper is focused on the numerical modeling of welded steel bearing elements using commercial software system ANSYS, which is based on the finite element method - FEM. It is important to check and compare the results of FEM analysis with the results of physical verification test, in which the real behavior of the bearing element can be observed. The results of the comparison can be used for calibration of the computational model. The article deals with the physical test of steel supporting elements, whose main purpose is obtaining of material, geometry and strength characteristics of the fillet and butt welds including heat affected zone in the basic material of welded steel bearing element. The pressure test was performed during the experiment, wherein the total load value and the corresponding deformation of the specimens under the load was monitored. Obtained data were used for the calibration of numerical models of test samples and they are necessary for further stress and strain analysis of steel supporting elements.

Název v anglickém jazyce

Static behavior of the weld in the joint of the steel support element using experiment and numerical modeling

Popis výsledku anglicky

The paper is focused on the numerical modeling of welded steel bearing elements using commercial software system ANSYS, which is based on the finite element method - FEM. It is important to check and compare the results of FEM analysis with the results of physical verification test, in which the real behavior of the bearing element can be observed. The results of the comparison can be used for calibration of the computational model. The article deals with the physical test of steel supporting elements, whose main purpose is obtaining of material, geometry and strength characteristics of the fillet and butt welds including heat affected zone in the basic material of welded steel bearing element. The pressure test was performed during the experiment, wherein the total load value and the corresponding deformation of the specimens under the load was monitored. Obtained data were used for the calibration of numerical models of test samples and they are necessary for further stress and strain analysis of steel supporting elements.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20102 - Construction engineering, Municipal and structural engineering

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

IOP Conference Series: Earth and Environmental Science. Volume 143

ISBN

—

ISSN

1755-1307

e-ISSN

1755-1315

Počet stran výsledku

8

Strana od-do

1-8

Název nakladatele

IOP Publishing

Místo vydání

Bristol

Místo konání akce

Ho Či Minovo Město

Datum konání akce

17. 4. 2018

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000447721000004