Blank designing for drawing of stampings
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F01%3A86081814" target="_blank" >RIV/61989100:27230/01:86081814 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Blank designing for drawing of stampings
Popis výsledku v původním jazyce
Contribution concerns determining of optimal shape and size of blank for drawing of intricate shape stampings. Intricate shape stampings demonstrate unusual characteristic as opposed to the drawing of cylindrical cups; the stress and strain behavior is more complex and the deformation is, moreover, affected by the blank shape, size and orientation. Three methods - the method according to the Czech State Standards, the method of sections and the graphical method, using the maximum shear stress trajectories - were discussed and additionally used for determining of shape and size of blank for drawing of selected stamping of intricate shape. The results of drawing of stamping from three variants of blanks have shown, that the blank, determined by graphicalmethod, using the M. S. S. T., is the optimal solution. Using of this blank shape is one of the principal assumption of removing of the rejection in practice.
Název v anglickém jazyce
Blank designing for drawing of stampings
Popis výsledku anglicky
Contribution concerns determining of optimal shape and size of blank for drawing of intricate shape stampings. Intricate shape stampings demonstrate unusual characteristic as opposed to the drawing of cylindrical cups; the stress and strain behavior is more complex and the deformation is, moreover, affected by the blank shape, size and orientation. Three methods - the method according to the Czech State Standards, the method of sections and the graphical method, using the maximum shear stress trajectories - were discussed and additionally used for determining of shape and size of blank for drawing of selected stamping of intricate shape. The results of drawing of stamping from three variants of blanks have shown, that the blank, determined by graphicalmethod, using the M. S. S. T., is the optimal solution. Using of this blank shape is one of the principal assumption of removing of the rejection in practice.
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JR - Ostatní strojírenství
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/GA101%2F00%2F0488" target="_blank" >GA101/00/0488: Rozpracování metodiky stanovení tvaru a velikosti přístřihu pro tažení dutých výtažků nepravidelných tvarů z tenkých plechů</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>Z - Vyzkumny zamer (s odkazem do CEZ)
Ostatní
Rok uplatnění
2001
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Sborník vědeckých prací Vysoké školy báňské - Technické univerzity Ostrava. Řada strojní
ISSN
1210-0471
e-ISSN
—
Svazek periodika
47
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
10
Strana od-do
37-46
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—