Evaluation of the deep-drawing steel sheets processed by DRECE device
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F15%3A86097428" target="_blank" >RIV/61989100:27230/15:86097428 - isvavai.cz</a>
Výsledek na webu
<a href="http://konsys-t.tanger.cz/files/proceedings/19/reports/3528.pdf" target="_blank" >http://konsys-t.tanger.cz/files/proceedings/19/reports/3528.pdf</a>
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Evaluation of the deep-drawing steel sheets processed by DRECE device
Popis výsledku v původním jazyce
The process of forming of material using the DRECE technique is based on making use of the material's intensive plastic deformation, i.e. that process is a combination of two known technologies, ECAP and CONFORM. Findings: The article presents the results of both exams, including photographs of cracks. Mechanical properties of thesteel grade11 321 before and after extrusion by DRECE tool are described as well. Research limitations/implications: The article describes the process of forming of metal sheets made of steel grade 11 321. It further describes two methods for detection of deep drawing - Erichsen and Fukui. Originality/value: The article describes the process of forming of metal sheets made of steel grade 11 321. It further describes two methods for detection of deep drawing - Erichsen and Fukui. These methods were applied to the extruded metal sheet by DRECE tools.
Název v anglickém jazyce
Evaluation of the deep-drawing steel sheets processed by DRECE device
Popis výsledku anglicky
The process of forming of material using the DRECE technique is based on making use of the material's intensive plastic deformation, i.e. that process is a combination of two known technologies, ECAP and CONFORM. Findings: The article presents the results of both exams, including photographs of cracks. Mechanical properties of thesteel grade11 321 before and after extrusion by DRECE tool are described as well. Research limitations/implications: The article describes the process of forming of metal sheets made of steel grade 11 321. It further describes two methods for detection of deep drawing - Erichsen and Fukui. Originality/value: The article describes the process of forming of metal sheets made of steel grade 11 321. It further describes two methods for detection of deep drawing - Erichsen and Fukui. These methods were applied to the extruded metal sheet by DRECE tools.
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JR - Ostatní strojírenství
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2015
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Archives of Materials Science and Engineering
ISSN
1897-2764
e-ISSN
—
Svazek periodika
68
Číslo periodika v rámci svazku
1
Stát vydavatele periodika
PL - Polská republika
Počet stran výsledku
5
Strana od-do
31-35
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-84922530659