CFD Analysis of the Plate Heat Exchanger - Mathematical Modelling of Mass and Heat Transfer in Serial Connection with Tubular Heat Exchanger
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F16%3A86098015" target="_blank" >RIV/61989100:27230/16:86098015 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/61989100:27360/16:86098015
Výsledek na webu
<a href="http://dx.doi.org/10.1063/1.4953696" target="_blank" >http://dx.doi.org/10.1063/1.4953696</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1063/1.4953696" target="_blank" >10.1063/1.4953696</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
CFD Analysis of the Plate Heat Exchanger - Mathematical Modelling of Mass and Heat Transfer in Serial Connection with Tubular Heat Exchanger
Popis výsledku v původním jazyce
Application of numerical simulations based on the CFD calculation when the mass and heat transfer between the fluid flows is essential component of thermal calculation. In this article the mathematical model of the heat exchanger is defined, which is subsequently applied to the plate heat exchanger, which is connected in series with the other heat exchanger (tubular heat exchanger). The present contribution deals with the possibility to use the waste heat of the flue gas produced by small micro turbine. Inlet boundary conditions to the mathematical model of the plate heat exchanger are obtained from the results of numerical simulation of the tubular heat exchanger. Required parameters such for example inlet temperature was evaluated from temperature field, which was subsequently imported to the inlet boundary condition to the simulation of plate heat exchanger. From the results of 3D numerical simulations are evaluated basic flow variables including the evaluation of dimensionless parameters such as Colburn j-factor and friction f(t) factor. Numerical simulation is realized by software ANSYS Fluent15.0.
Název v anglickém jazyce
CFD Analysis of the Plate Heat Exchanger - Mathematical Modelling of Mass and Heat Transfer in Serial Connection with Tubular Heat Exchanger
Popis výsledku anglicky
Application of numerical simulations based on the CFD calculation when the mass and heat transfer between the fluid flows is essential component of thermal calculation. In this article the mathematical model of the heat exchanger is defined, which is subsequently applied to the plate heat exchanger, which is connected in series with the other heat exchanger (tubular heat exchanger). The present contribution deals with the possibility to use the waste heat of the flue gas produced by small micro turbine. Inlet boundary conditions to the mathematical model of the plate heat exchanger are obtained from the results of numerical simulation of the tubular heat exchanger. Required parameters such for example inlet temperature was evaluated from temperature field, which was subsequently imported to the inlet boundary condition to the simulation of plate heat exchanger. From the results of 3D numerical simulations are evaluated basic flow variables including the evaluation of dimensionless parameters such as Colburn j-factor and friction f(t) factor. Numerical simulation is realized by software ANSYS Fluent15.0.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
JE - Nejaderná energetika, spotřeba a užití energie
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2016
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
AIP Conference Proceedings. Volume 1745
ISBN
978-0-7354-1402-0
ISSN
0094-243X
e-ISSN
—
Počet stran výsledku
9
Strana od-do
1-9
Název nakladatele
American Institute of Physics
Místo vydání
New York
Místo konání akce
Terchova
Datum konání akce
27. 4. 2016
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
000380817100002