Development of geometry of forming tools for extrusion of strip sheet by SPD process

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F17%3A10229658" target="_blank" >RIV/61989100:27230/17:10229658 - isvavai.cz</a>

Výsledek na webu

<a href="http://iopscience.iop.org/article/10.1088/1757-899X/179/1/012061/pdf" target="_blank" >http://iopscience.iop.org/article/10.1088/1757-899X/179/1/012061/pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/1757-899X/179/1/012061" target="_blank" >10.1088/1757-899X/179/1/012061</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Development of geometry of forming tools for extrusion of strip sheet by SPD process

Popis výsledku v původním jazyce

On VSB -Technical University of Ostrava developed a method that uses the principle of severe plastic deformation to refine the structure and enhance mechanical properties of sheet metal strips. The greatest importance in practice represents an increase in yield strength and ultimate strength of sheet metal strips. The DRECE method (Dual Rolls Equal Channel Extrusion) is a newly developed method. Severe plastic deformation results in a high degree of the material deformation. The method can be used to produce metallic materials with a very fine grain structure. The paper analyses the effects of the values of angles of the newly developed forming tools on the achievement of mechanical properties in selected carbon steels by SPD process. The one type of steels (Ck55) was verified experimentally. Experiments were performed on the sheet metal strip with dimensions 58 (width) 2 (thickness) 1000 (length) mm with different inclination angle α.

Název v anglickém jazyce

Development of geometry of forming tools for extrusion of strip sheet by SPD process

Popis výsledku anglicky

On VSB -Technical University of Ostrava developed a method that uses the principle of severe plastic deformation to refine the structure and enhance mechanical properties of sheet metal strips. The greatest importance in practice represents an increase in yield strength and ultimate strength of sheet metal strips. The DRECE method (Dual Rolls Equal Channel Extrusion) is a newly developed method. Severe plastic deformation results in a high degree of the material deformation. The method can be used to produce metallic materials with a very fine grain structure. The paper analyses the effects of the values of angles of the newly developed forming tools on the achievement of mechanical properties in selected carbon steels by SPD process. The one type of steels (Ck55) was verified experimentally. Experiments were performed on the sheet metal strip with dimensions 58 (width) 2 (thickness) 1000 (length) mm with different inclination angle α.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

IOP Conference Series: Materials Science and Engineering. Volume 179

ISSN

1757-8981

e-ISSN

—

Svazek periodika

179

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

11

Strana od-do

1-11

Kód UT WoS článku

000403407100061

EID výsledku v databázi Scopus

2-s2.0-85016497355