Method of non-contact measuring of diameter and ovality of steel tubes during their production

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F19%3A10242400" target="_blank" >RIV/61989100:27230/19:10242400 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mmscience.eu/journal/issues/march-2019/articles/method-of-non-contact-measuring-of-diameter-and-ovality-of-steel-tubes-during-their-production" target="_blank" >https://www.mmscience.eu/journal/issues/march-2019/articles/method-of-non-contact-measuring-of-diameter-and-ovality-of-steel-tubes-during-their-production</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2019_03_201898" target="_blank" >10.17973/MMSJ.2019_03_201898</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Method of non-contact measuring of diameter and ovality of steel tubes during their production

Popis výsledku v původním jazyce

The quality of production of metallurgical bar stock, in particular tubes, is assessed based on many production parameters including outer cross section (diameter) and ovality, which are also specified by European standard EN 13 508. Tubes need to be measured as soon as possible, ideally immediately after the rolling mill during their production, so that any defects may be corrected in due time and thus the loss of material and power may be minimized. This means that the tubes need to be measured at high temperatures (approximately 1.000 oC). The article describes a new method of non-contact measuring of outer diameters and ovality of steel tubes cross sections that meets the above-mentioned requirements and allows reliable measuring of required parameters even in the case when the measured material moves or vibrates vertically during measuring. (C) 2019, MM publishing Ltd. All rights reserved.

Název v anglickém jazyce

Method of non-contact measuring of diameter and ovality of steel tubes during their production

Popis výsledku anglicky

The quality of production of metallurgical bar stock, in particular tubes, is assessed based on many production parameters including outer cross section (diameter) and ovality, which are also specified by European standard EN 13 508. Tubes need to be measured as soon as possible, ideally immediately after the rolling mill during their production, so that any defects may be corrected in due time and thus the loss of material and power may be minimized. This means that the tubes need to be measured at high temperatures (approximately 1.000 oC). The article describes a new method of non-contact measuring of outer diameters and ovality of steel tubes cross sections that meets the above-mentioned requirements and allows reliable measuring of required parameters even in the case when the measured material moves or vibrates vertically during measuring. (C) 2019, MM publishing Ltd. All rights reserved.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/EF16_019%2F0000867" target="_blank" >EF16_019/0000867: Centrum výzkumu pokročilých mechatronických systémů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

—

Svazek periodika

2019

Číslo periodika v rámci svazku

March

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

2855-2860

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85065015155