Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Elimination of impact bed dustiness

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F19%3A10242788" target="_blank" >RIV/61989100:27230/19:10242788 - isvavai.cz</a>

  • Výsledek na webu

    <a href="http://dx.doi.org/10.5593/sgem2019/1.3/S03.034" target="_blank" >http://dx.doi.org/10.5593/sgem2019/1.3/S03.034</a>

  • DOI - Digital Object Identifier

    <a href="http://dx.doi.org/10.5593/sgem2019/1.3/S03.034" target="_blank" >10.5593/sgem2019/1.3/S03.034</a>

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Elimination of impact bed dustiness

  • Popis výsledku v původním jazyce

    Conveyor belts are used for conveying both loose and lump materials in surface mines. During their transport, especially in the places of pouring these materials, where the material is crushed due to a large impact height, a large amount of dust is generated. This makes problems in the actual operation due to fire or explosion hazards, and also by fouling up the vicinity of conveyor belts and transfer points. The resulting dust also poses a threat to the health of operators. Most of the resulting dust accumulates in the vicinity of the dust source, but particles less than 5μm remain in the air permanently and can be distributed over large distances according to weather conditions, thereby endangering the health of people living around a surface mine. Many technical solutions can be used to eliminate dust on conveyor belts, for which the common solution is the use of variously shaped covers for the transfer points. Different types of impact beds can also be used, with the impact part designed to lower the amount of crushed coal and allowing for the use of vertical side seals. The aim of this article is to compare 2 technical solutions, which are used to prevent dust leakage from conveyor belts into the air. There is a wet method of dust removal, represented by sprinkling the transported material or misting the area of dust, and a dry method of dust extraction and its elimination from an air mass using a filtration device. (C) 2019, International Multidisciplinary Scientific Geoconference. All rights received.

  • Název v anglickém jazyce

    Elimination of impact bed dustiness

  • Popis výsledku anglicky

    Conveyor belts are used for conveying both loose and lump materials in surface mines. During their transport, especially in the places of pouring these materials, where the material is crushed due to a large impact height, a large amount of dust is generated. This makes problems in the actual operation due to fire or explosion hazards, and also by fouling up the vicinity of conveyor belts and transfer points. The resulting dust also poses a threat to the health of operators. Most of the resulting dust accumulates in the vicinity of the dust source, but particles less than 5μm remain in the air permanently and can be distributed over large distances according to weather conditions, thereby endangering the health of people living around a surface mine. Many technical solutions can be used to eliminate dust on conveyor belts, for which the common solution is the use of variously shaped covers for the transfer points. Different types of impact beds can also be used, with the impact part designed to lower the amount of crushed coal and allowing for the use of vertical side seals. The aim of this article is to compare 2 technical solutions, which are used to prevent dust leakage from conveyor belts into the air. There is a wet method of dust removal, represented by sprinkling the transported material or misting the area of dust, and a dry method of dust extraction and its elimination from an air mass using a filtration device. (C) 2019, International Multidisciplinary Scientific Geoconference. All rights received.

Klasifikace

  • Druh

    D - Stať ve sborníku

  • CEP obor

  • OECD FORD obor

    20300 - Mechanical engineering

Návaznosti výsledku

  • Projekt

  • Návaznosti

    S - Specificky vyzkum na vysokych skolach

Ostatní

  • Rok uplatnění

    2019

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název statě ve sborníku

    19th International Multidisciplinary Scientific GeoConference : SGEM 2019 : conference proceedings : 30 June - 6 July, 2019, Albena, Bulgaria. Volume 19. Issue 1.3

  • ISBN

    978-619-7408-78-2

  • ISSN

    1314-2704

  • e-ISSN

  • Počet stran výsledku

    8

  • Strana od-do

    271-278

  • Název nakladatele

    STEF92 Technology Ltd.

  • Místo vydání

    Sofia

  • Místo konání akce

    Albena

  • Datum konání akce

    30. 6. 2019

  • Typ akce podle státní příslušnosti

    WRD - Celosvětová akce

  • Kód UT WoS článku