Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Experimental analysis of temperature resistance of 3d printed PLA components

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F21%3A10247421" target="_blank" >RIV/61989100:27230/21:10247421 - isvavai.cz</a>

  • Nalezeny alternativní kódy

    RIV/61989100:27730/21:10247421

  • Výsledek na webu

    <a href="https://www.mmscience.eu/journal/issues/march-2021/articles/experimental-analysis-of-temperature-resistance-of-3d-printed-pla-components" target="_blank" >https://www.mmscience.eu/journal/issues/march-2021/articles/experimental-analysis-of-temperature-resistance-of-3d-printed-pla-components</a>

  • DOI - Digital Object Identifier

    <a href="http://dx.doi.org/10.17973/MMSJ.2021_03_2021004" target="_blank" >10.17973/MMSJ.2021_03_2021004</a>

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Experimental analysis of temperature resistance of 3d printed PLA components

  • Popis výsledku v původním jazyce

    PLA is one of the most widely used materials in additive technology, especially in the Fused Filament Fabrication method. However, its use is limited by its relatively low-temperature resistance. The glass transition temperature of PLA is around 60 oC. Some studies already performed on the annealing of 3D printed plastics have shown their increased heat deflection temperature. However, the interpretation of some of these studies&apos; results does not correspond to our practical experience. For example, one of those works reports that annealed PLA samples soften at much higher temperatures than the original nonannealed ones. This paper intends to better understand the behaviour of annealed printed PLA samples at higher temperatures and extends previously performed studies to determine glass transition temperatures using TGA. The samples are tested in two devices to determine the temperature resistance. The first is based on the standard for determining the heat deflection temperature according to ISO 75. In the second device, the sample is subjected to tensile stress at a specific temperature under the simultaneous action of stress induced from the screw connection. The results show that the annealed samples&apos; glass transition temperature does not differ significantly compared to the nonannealed samples. Furthermore, tests have shown that annealed samples deform under relatively small load at higher temperatures than nonannealed samples, but this deformation depends on its magnitude. If the load is high enough, the annealed specimens deform at the same temperature as the nonannealed specimens.

  • Název v anglickém jazyce

    Experimental analysis of temperature resistance of 3d printed PLA components

  • Popis výsledku anglicky

    PLA is one of the most widely used materials in additive technology, especially in the Fused Filament Fabrication method. However, its use is limited by its relatively low-temperature resistance. The glass transition temperature of PLA is around 60 oC. Some studies already performed on the annealing of 3D printed plastics have shown their increased heat deflection temperature. However, the interpretation of some of these studies&apos; results does not correspond to our practical experience. For example, one of those works reports that annealed PLA samples soften at much higher temperatures than the original nonannealed ones. This paper intends to better understand the behaviour of annealed printed PLA samples at higher temperatures and extends previously performed studies to determine glass transition temperatures using TGA. The samples are tested in two devices to determine the temperature resistance. The first is based on the standard for determining the heat deflection temperature according to ISO 75. In the second device, the sample is subjected to tensile stress at a specific temperature under the simultaneous action of stress induced from the screw connection. The results show that the annealed samples&apos; glass transition temperature does not differ significantly compared to the nonannealed samples. Furthermore, tests have shown that annealed samples deform under relatively small load at higher temperatures than nonannealed samples, but this deformation depends on its magnitude. If the load is high enough, the annealed specimens deform at the same temperature as the nonannealed specimens.

Klasifikace

  • Druh

    J<sub>imp</sub> - Článek v periodiku v databázi Web of Science

  • CEP obor

    —

  • OECD FORD obor

    20301 - Mechanical engineering

Návaznosti výsledku

  • Projekt

    <a href="/cs/project/EF16_019%2F0000867" target="_blank" >EF16_019/0000867: Centrum výzkumu pokročilých mechatronických systémů</a><br>

  • Návaznosti

    P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Ostatní

  • Rok uplatnění

    2021

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název periodika

    MM Science Journal

  • ISSN

    1803-1269

  • e-ISSN

    —

  • Svazek periodika

    2021

  • Číslo periodika v rámci svazku

    March

  • Stát vydavatele periodika

    CZ - Česká republika

  • Počet stran výsledku

    6

  • Strana od-do

    4322-4327

  • Kód UT WoS článku

    000634572700014

  • EID výsledku v databázi Scopus

    2-s2.0-85102776943