Ultrasonic Pulsating Water Jet Peening: Influence of Pressure and Pattern Strategy

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F21%3A10248585" target="_blank" >RIV/61989100:27230/21:10248585 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/44555601:13420/22:43896685

Výsledek na webu

<a href="https://www.webofscience.com/wos/alldb/full-record/WOS:000713787700001" target="_blank" >https://www.webofscience.com/wos/alldb/full-record/WOS:000713787700001</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma14206019" target="_blank" >10.3390/ma14206019</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Ultrasonic Pulsating Water Jet Peening: Influence of Pressure and Pattern Strategy

Popis výsledku v původním jazyce

Peening techniques are nowadays attracting more research attention due to their association with the extending of the service life and improving surface texture of engineering components. Ultrasonic pulsating water jet peening represents a new way of mechanical surface treatment. Accelerated water droplets via hammer effect cause small elastic-plastic deformations on the surface. This work deals with peening of aluminum alloy using an ultrasonic pulsating water jet, where periodically acting water droplets were used as the peening medium. The aim of the work was the feasibility study of the peening process and to observe the effects of pressure (p = 10, 20 and 30 MPa) and pattern trajectory (linear hatch and cross hatch). The peened surfaces were analyzed by the surface roughness profile parameters Ra and Rz and the microhardness along the peening axis into the material. Graphically processed results show a clear increase of measured values with increasing pressure (p = 10, 20 and 30 MPa), where the roughness values ranged from 1.89 mu m to 4.11 mu m, and the microhardness values ranged from 43.3 HV0.005 to 47 HV0.005, as compared to 40.3 HV0.005 obtained for the untreated sample. The achieved results indicate potential using of an ultrasonic pulsating water jet as a new method of surface treatment of metals. By controlled distribution of water droplets, it is possible to achieve a local distribution of surface roughness, and at the same time, strengthening of the subsurface layers in the material without thermal influence on the material.&lt;/p&gt;

Název v anglickém jazyce

Ultrasonic Pulsating Water Jet Peening: Influence of Pressure and Pattern Strategy

Popis výsledku anglicky

Peening techniques are nowadays attracting more research attention due to their association with the extending of the service life and improving surface texture of engineering components. Ultrasonic pulsating water jet peening represents a new way of mechanical surface treatment. Accelerated water droplets via hammer effect cause small elastic-plastic deformations on the surface. This work deals with peening of aluminum alloy using an ultrasonic pulsating water jet, where periodically acting water droplets were used as the peening medium. The aim of the work was the feasibility study of the peening process and to observe the effects of pressure (p = 10, 20 and 30 MPa) and pattern trajectory (linear hatch and cross hatch). The peened surfaces were analyzed by the surface roughness profile parameters Ra and Rz and the microhardness along the peening axis into the material. Graphically processed results show a clear increase of measured values with increasing pressure (p = 10, 20 and 30 MPa), where the roughness values ranged from 1.89 mu m to 4.11 mu m, and the microhardness values ranged from 43.3 HV0.005 to 47 HV0.005, as compared to 40.3 HV0.005 obtained for the untreated sample. The achieved results indicate potential using of an ultrasonic pulsating water jet as a new method of surface treatment of metals. By controlled distribution of water droplets, it is possible to achieve a local distribution of surface roughness, and at the same time, strengthening of the subsurface layers in the material without thermal influence on the material.&lt;/p&gt;

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/EF17_049%2F0008407" target="_blank" >EF17_049/0008407: Inovativní a aditivní technologie výroby - nová technologická řešení 3D tisku kovů a kompozitních materiálů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

—

Svazek periodika

14

Číslo periodika v rámci svazku

20

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

17

Strana od-do

—

Kód UT WoS článku

000713787700001

EID výsledku v databázi Scopus

2-s2.0-85120850990