Applied forces in the handling unit fixation mechanism

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F22%3A10244507" target="_blank" >RIV/61989100:27230/22:10244507 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/61989100:27240/22:10244507

Výsledek na webu

<a href="https://hrcak.srce.hr/272614" target="_blank" >https://hrcak.srce.hr/272614</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17559/TV-20200319070344" target="_blank" >10.17559/TV-20200319070344</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Applied forces in the handling unit fixation mechanism

Popis výsledku v původním jazyce

The paper presents a construction design of a testing device, which was built for the purpose of checking the functional properties of the movement fixation mechanism of handling units, which is used for locking pallets with cars in place in some parking houses, developed by the enterprise KOMA Industry s.r.o. The testing device uses two positioning tables, whose moving parts are attached perpendicular to each other in the frame of the testing device. A pallet lock is attached to the sliding part of the vertical positioning table, which consists of three basic parts: body, pulley holder and compression coil spring. A plate is attached to the sliding part of the horizontal positioning device which is adapted to receive the stop of the fixation mechanism. Chapter 2.1. of this paper presents values of the measured vertical forces acting on the force transducer, which were generated by the reshaped coil spring with a wire of circular cross-section during the rolling of the pallet lock roller over the sloped surface of the stop. Section 2.2. presents an experimental procedure and the results of the measured vertical forces exerted by a reshaped coil spring with a wire of circular cross-section on the force sensor during the insertion of the pulley roller into the gap between the two end faces of the stop assembly. The experimental procedure and the results of the measured vertical forces exerted by the reshaped coil spring with a wire of circular cross-section on the force sensor during sliding of the lock pulley roller out of the gap in the stop are given in section 2.3. The conducted experimental measurements of the functional properties of the fixation lock of the pallet and the acquired values of acting vertical forces will serve to optimize the attaching of pallet fixation locks to the steel girders of the structure of the cell rack parking space of the automatic parking house, over which the chain conveyer transports pallets with vehicles into specified parking positions.

Název v anglickém jazyce

Applied forces in the handling unit fixation mechanism

Popis výsledku anglicky

The paper presents a construction design of a testing device, which was built for the purpose of checking the functional properties of the movement fixation mechanism of handling units, which is used for locking pallets with cars in place in some parking houses, developed by the enterprise KOMA Industry s.r.o. The testing device uses two positioning tables, whose moving parts are attached perpendicular to each other in the frame of the testing device. A pallet lock is attached to the sliding part of the vertical positioning table, which consists of three basic parts: body, pulley holder and compression coil spring. A plate is attached to the sliding part of the horizontal positioning device which is adapted to receive the stop of the fixation mechanism. Chapter 2.1. of this paper presents values of the measured vertical forces acting on the force transducer, which were generated by the reshaped coil spring with a wire of circular cross-section during the rolling of the pallet lock roller over the sloped surface of the stop. Section 2.2. presents an experimental procedure and the results of the measured vertical forces exerted by a reshaped coil spring with a wire of circular cross-section on the force sensor during the insertion of the pulley roller into the gap between the two end faces of the stop assembly. The experimental procedure and the results of the measured vertical forces exerted by the reshaped coil spring with a wire of circular cross-section on the force sensor during sliding of the lock pulley roller out of the gap in the stop are given in section 2.3. The conducted experimental measurements of the functional properties of the fixation lock of the pallet and the acquired values of acting vertical forces will serve to optimize the attaching of pallet fixation locks to the steel girders of the structure of the cell rack parking space of the automatic parking house, over which the chain conveyer transports pallets with vehicles into specified parking positions.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Tehnički vjesnik – Technical Gazette

ISSN

1330-3651

e-ISSN

1848-6339

Svazek periodika

29

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

HR - Chorvatská republika

Počet stran výsledku

8

Strana od-do

620-627

Kód UT WoS článku

000760151800011

EID výsledku v databázi Scopus

2-s2.0-85125056218