Optimization of Process Variables in the Drilling of LM6/B4C Composites through Grey Relational Analysis
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F22%3A10250065" target="_blank" >RIV/61989100:27230/22:10250065 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:000832207800001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:000832207800001</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.3390/ma15144860" target="_blank" >10.3390/ma15144860</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Optimization of Process Variables in the Drilling of LM6/B4C Composites through Grey Relational Analysis
Popis výsledku v původním jazyce
The objective of this investigational analysis was to study the influence of process variables on the response during the drilling of LM6/B4C composite materials. Stir casting was employed to produce the LM6/B4C composites. A Vertical Machining Center (VMC) with a dynamometer was used to drill the holes and to record the thrust force. An L27 orthogonal array was used to carry out the experimental work. A grey relational analysis (GRA) was employed to perform optimization in order to attain the lowest Thrust Force (TF), Surface Roughness (SR) and Burr Height (BH). For minimal responses, the optimum levels of the process variables viz. the feed rate (F), spindle speed (S), drill material (D) and reinforcing percentage (R) were determined. The process variables in the drilling of the LM6/B4C composites were indeed optimized, according to confirmational investigations. The predicted Grey Relational Grade was 0.846, whereas the experimental GRG was 0.865, with a 2.2% error-indicating that the optimization process was valid.
Název v anglickém jazyce
Optimization of Process Variables in the Drilling of LM6/B4C Composites through Grey Relational Analysis
Popis výsledku anglicky
The objective of this investigational analysis was to study the influence of process variables on the response during the drilling of LM6/B4C composite materials. Stir casting was employed to produce the LM6/B4C composites. A Vertical Machining Center (VMC) with a dynamometer was used to drill the holes and to record the thrust force. An L27 orthogonal array was used to carry out the experimental work. A grey relational analysis (GRA) was employed to perform optimization in order to attain the lowest Thrust Force (TF), Surface Roughness (SR) and Burr Height (BH). For minimal responses, the optimum levels of the process variables viz. the feed rate (F), spindle speed (S), drill material (D) and reinforcing percentage (R) were determined. The process variables in the drilling of the LM6/B4C composites were indeed optimized, according to confirmational investigations. The predicted Grey Relational Grade was 0.846, whereas the experimental GRG was 0.865, with a 2.2% error-indicating that the optimization process was valid.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20300 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2022
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Materials
ISSN
1996-1944
e-ISSN
1996-1944
Svazek periodika
15
Číslo periodika v rámci svazku
14
Stát vydavatele periodika
CH - Švýcarská konfederace
Počet stran výsledku
15
Strana od-do
nestrankovano
Kód UT WoS článku
000832207800001
EID výsledku v databázi Scopus
—