An Investigation into Sheet-Inconel 718 Forming with Flexible and Metal Tools - Simulation and Experiment

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F24%3A10255051" target="_blank" >RIV/61989100:27230/24:10255051 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.3390/ma17133168" target="_blank" >https://doi.org/10.3390/ma17133168</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma17133168" target="_blank" >10.3390/ma17133168</a>

Jazyk výsledku

angličtina

Název v původním jazyce

An Investigation into Sheet-Inconel 718 Forming with Flexible and Metal Tools - Simulation and Experiment

Popis výsledku v původním jazyce

The article presents the results of numerical simulations and experimental tests of plastic forming of sheets made from the difficult-to-deform nickel alloy Inconel 718 with a thickness of 1 mm, using punches made from elastomeric materials with hardness 50-90 Shore A and steel dies. Elastomeric stamps were created in the form of five layers with a diameter of 160 mm. The influence of the hardness of the elastomeric punches on the geometry of the elements obtained was determined. The dies were made from 90MnCrV8 steel with a hardness of over 60 HRC. Their task was to obtain the expected shape of the element while generating various stress states in specific areas of the semi-finished product. The research was carried out using an original device whose operating principle was based on the Guerin method. The shape and dimensions of the elements made from Inconel 718 nickel alloy were determined by optical 3D scanning. The geometry of the drawpiece showed a significant impact of the hardness of the layered elastomer matrices on the degree of shape reproduction. The results obtained from numerical modeling were confirmed by the results of experimental tests. It has been shown that the hardness of the elastomeric material used for punches for plastic forming Inconel 718 nickel alloy sheets should be adapted to the shape of the drawpiece. It was also found that one of the important aspects of plastic forming sheets using the Guerin method is the tendency to obtain a diversified shape of the final elements.

Název v anglickém jazyce

An Investigation into Sheet-Inconel 718 Forming with Flexible and Metal Tools - Simulation and Experiment

Popis výsledku anglicky

The article presents the results of numerical simulations and experimental tests of plastic forming of sheets made from the difficult-to-deform nickel alloy Inconel 718 with a thickness of 1 mm, using punches made from elastomeric materials with hardness 50-90 Shore A and steel dies. Elastomeric stamps were created in the form of five layers with a diameter of 160 mm. The influence of the hardness of the elastomeric punches on the geometry of the elements obtained was determined. The dies were made from 90MnCrV8 steel with a hardness of over 60 HRC. Their task was to obtain the expected shape of the element while generating various stress states in specific areas of the semi-finished product. The research was carried out using an original device whose operating principle was based on the Guerin method. The shape and dimensions of the elements made from Inconel 718 nickel alloy were determined by optical 3D scanning. The geometry of the drawpiece showed a significant impact of the hardness of the layered elastomer matrices on the degree of shape reproduction. The results obtained from numerical modeling were confirmed by the results of experimental tests. It has been shown that the hardness of the elastomeric material used for punches for plastic forming Inconel 718 nickel alloy sheets should be adapted to the shape of the drawpiece. It was also found that one of the important aspects of plastic forming sheets using the Guerin method is the tendency to obtain a diversified shape of the final elements.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

1996-1944

Svazek periodika

17

Číslo periodika v rámci svazku

June 2024

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

24

Strana od-do

1-24

Kód UT WoS článku

001269898700001

EID výsledku v databázi Scopus

2-s2.0-85198391188