Modal Parameters Estimation of Circular Plates Manufactured by FDM Technique Using Vibrometry: A Comparative Study

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F24%3A10255950" target="_blank" >RIV/61989100:27230/24:10255950 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/2076-3417/14/22/10609" target="_blank" >https://www.mdpi.com/2076-3417/14/22/10609</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/app142210609" target="_blank" >10.3390/app142210609</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Modal Parameters Estimation of Circular Plates Manufactured by FDM Technique Using Vibrometry: A Comparative Study

Popis výsledku v původním jazyce

This paper presents a comparative study focused on a modal parameters estimation of specimens manufactured by the FDM technique using a fixed embedded vibrometer based on the laser Doppler principle and roving hammer-impact method. Part of this paper is devoted to testing a fixed circular plate with a honeycomb infill pattern while varying the number of excitation points (DOFs), the number of analysis lines of fast Fourier transformation (FFT), and the locations or numbers of reference degrees of freedom (REFs). Although these parameters did not significantly affect the values found for the natural frequencies of the structure, there were changes in the estimates of the mode shapes (affected by the low number of DOFs), in the height and sharpness of the peaks of the CMIF functions (caused by the increased number of FFT lines), and in the number of identified modes (influenced by the chosen location(s) of REFs), respectively. Subsequently, the authors compared the results of experimental modal analyses carried out under the same conditions on three circular plates with honeycomb, star, and concentric infill patterns made of PLA. The results confirm that specimens with honeycomb or star infill patterns have a higher stiffness than those with concentric infill patterns. The low values of the damping ratios obtained for each structure indicate a strong response to excitation at or near their natural frequencies.

Název v anglickém jazyce

Modal Parameters Estimation of Circular Plates Manufactured by FDM Technique Using Vibrometry: A Comparative Study

Popis výsledku anglicky

This paper presents a comparative study focused on a modal parameters estimation of specimens manufactured by the FDM technique using a fixed embedded vibrometer based on the laser Doppler principle and roving hammer-impact method. Part of this paper is devoted to testing a fixed circular plate with a honeycomb infill pattern while varying the number of excitation points (DOFs), the number of analysis lines of fast Fourier transformation (FFT), and the locations or numbers of reference degrees of freedom (REFs). Although these parameters did not significantly affect the values found for the natural frequencies of the structure, there were changes in the estimates of the mode shapes (affected by the low number of DOFs), in the height and sharpness of the peaks of the CMIF functions (caused by the increased number of FFT lines), and in the number of identified modes (influenced by the chosen location(s) of REFs), respectively. Subsequently, the authors compared the results of experimental modal analyses carried out under the same conditions on three circular plates with honeycomb, star, and concentric infill patterns made of PLA. The results confirm that specimens with honeycomb or star infill patterns have a higher stiffness than those with concentric infill patterns. The low values of the damping ratios obtained for each structure indicate a strong response to excitation at or near their natural frequencies.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20302 - Applied mechanics

Projekt

—

Návaznosti

O - Projekt operacniho programu

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied Sciences

ISSN

2076-3417

e-ISSN

2076-3417

Svazek periodika

14

Číslo periodika v rámci svazku

22

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

25

Strana od-do

1-25

Kód UT WoS článku

001366705100001

EID výsledku v databázi Scopus

—