IMPACT OF EDGE PREPARATION ON SURFACE FINISHING PROPERTIES
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F24%3A10256052" target="_blank" >RIV/61989100:27230/24:10256052 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/61989100:27360/24:10256052
Výsledek na webu
<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:001350511600001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:001350511600001</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.17973/MMSJ.2024_11_2024083" target="_blank" >10.17973/MMSJ.2024_11_2024083</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
IMPACT OF EDGE PREPARATION ON SURFACE FINISHING PROPERTIES
Popis výsledku v původním jazyce
The properties of protective coatings made from organic coatings on metallic substrates strongly depend on the condition of the substrate surface. This refers to the condition of the edges, welds, and the surface in general. Edge treatment is one of the most important operations prior to the actual coating application. The coating's protective properties and its susceptibility to mechanical damage are directly affected by the edge treatment. The article deals with the problem of edge treatment of the base material and the effect of this treatment on the quality of surface finishing. The edges were modified in three ways on the prepared Kosmalt E 300 T samples. Subsequently, some samples were hot-dip galvanized. An organic coating was then applied as the final surface treatment to all samples. The evaluation of the quality of the surface finishing was carried out on the above-mentioned, differently treated edges. The results strongly indicate the importance of the condition of the substrate surface and its influence on the quality of the final surface finish.
Název v anglickém jazyce
IMPACT OF EDGE PREPARATION ON SURFACE FINISHING PROPERTIES
Popis výsledku anglicky
The properties of protective coatings made from organic coatings on metallic substrates strongly depend on the condition of the substrate surface. This refers to the condition of the edges, welds, and the surface in general. Edge treatment is one of the most important operations prior to the actual coating application. The coating's protective properties and its susceptibility to mechanical damage are directly affected by the edge treatment. The article deals with the problem of edge treatment of the base material and the effect of this treatment on the quality of surface finishing. The edges were modified in three ways on the prepared Kosmalt E 300 T samples. Subsequently, some samples were hot-dip galvanized. An organic coating was then applied as the final surface treatment to all samples. The evaluation of the quality of the surface finishing was carried out on the above-mentioned, differently treated edges. The results strongly indicate the importance of the condition of the substrate surface and its influence on the quality of the final surface finish.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2024
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
MM Science Journal
ISSN
1803-1269
e-ISSN
1805-0476
Svazek periodika
SI
Číslo periodika v rámci svazku
2024
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
5
Strana od-do
7591-7596
Kód UT WoS článku
001350511600001
EID výsledku v databázi Scopus
—