Synergetic effect of TiC particles on cavitation erosion resistance of AZ31-TiC surface composites
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F25%3A10259138" target="_blank" >RIV/61989100:27230/25:10259138 - isvavai.cz</a>
Výsledek na webu
<a href="https://linkinghub.elsevier.com/retrieve/pii/S240584402500982X" target="_blank" >https://linkinghub.elsevier.com/retrieve/pii/S240584402500982X</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.heliyon.2025.e42602" target="_blank" >10.1016/j.heliyon.2025.e42602</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Synergetic effect of TiC particles on cavitation erosion resistance of AZ31-TiC surface composites
Popis výsledku v původním jazyce
AZ31/TiC surface composites were produced using Friction Stir Processing (FSP), with varying amounts of TiC particles. The microstructure and hardness measurements, as well as the evaluation of erosion wear resistance, were carried out on AZ31/TiC composites. X-ray diffraction tests were carried out to identify the phase composition. The presence of α-Mg and TiC phases was observed in all composites and no chemical interactions between the AZ31 matrix and TiC were observed at the interface. The AZ31 alloy is shown to have a hardness of 62 The AZ31 alloy reinforced with 15 vol% of TiC particles showed the highest resistance to cavitation with volume loss of 44 mm3, while the AZ31 alloy showed the lowest resistance with volume loss of 142 mm3 for 15 min exposure time. HV ± 2 HV, whereas the AZ31/15 vol% of TiC composites is found to exhibit the highest hardness of 116 HV ± 5 HV. © 2025
Název v anglickém jazyce
Synergetic effect of TiC particles on cavitation erosion resistance of AZ31-TiC surface composites
Popis výsledku anglicky
AZ31/TiC surface composites were produced using Friction Stir Processing (FSP), with varying amounts of TiC particles. The microstructure and hardness measurements, as well as the evaluation of erosion wear resistance, were carried out on AZ31/TiC composites. X-ray diffraction tests were carried out to identify the phase composition. The presence of α-Mg and TiC phases was observed in all composites and no chemical interactions between the AZ31 matrix and TiC were observed at the interface. The AZ31 alloy is shown to have a hardness of 62 The AZ31 alloy reinforced with 15 vol% of TiC particles showed the highest resistance to cavitation with volume loss of 44 mm3, while the AZ31 alloy showed the lowest resistance with volume loss of 142 mm3 for 15 min exposure time. HV ± 2 HV, whereas the AZ31/15 vol% of TiC composites is found to exhibit the highest hardness of 116 HV ± 5 HV. © 2025
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
O - Projekt operacniho programu
Ostatní
Rok uplatnění
2025
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Heliyon
ISSN
2405-8440
e-ISSN
—
Svazek periodika
11
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
9
Strana od-do
"not paged"
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-85217429701