Masonry moisture measurement using the distributed temperature sensing system

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27240%2F17%3A10238697" target="_blank" >RIV/61989100:27240/17:10238697 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.scopus.com/record/display.uri?eid=2-s2.0-85023742617&origin=resultslist&sort=plf-f&src=s&sid=7e1dae5abbe8d74dd78e9b01cb00b5d5&sot=autdocs&sdt=autdocs&sl=18&s=AU-ID%2856519511800%29&relpos=2&citeCnt=0&searchTerm=" target="_blank" >https://www.scopus.com/record/display.uri?eid=2-s2.0-85023742617&origin=resultslist&sort=plf-f&src=s&sid=7e1dae5abbe8d74dd78e9b01cb00b5d5&sot=autdocs&sdt=autdocs&sl=18&s=AU-ID%2856519511800%29&relpos=2&citeCnt=0&searchTerm=</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Masonry moisture measurement using the distributed temperature sensing system

Popis výsledku v původním jazyce

Distributed temperature sensing systems (DTS) are based on the principle of time-domain reflectometry where an optical fiber acts as a temperature sensor. DTS is capable of measuring the temperature along the optical fiber using the nonlinear phenomenon referred as Raman scattering. The biggest advantage of such sensing system is the use of an optical fiber itself as a sensor which gives the benefits of electromagnetic interference immunity, low sensor cost, measurement distances up to 10 kilometers and the safe use in flammable and corrosive environments. Fiber optic DTS can be therefore used in the environments and processes in which the application of conventional sensors is impossible. This article discusses the use of DTS for the moisture measurement in the masonry. In structures with built-in optical fiber, the immediate detection and location of moisture are possible. To perform the measurements an experimental brick wall has been built and between each wall layer the optical fiber was placed. The wall was built in stainless steel tub with a drain valve and was placed on a mobile trolley. The dimensions of the wall were 106 x 100 x 30 cm. The actual measurements were carried out in two stages. In the first, the tub was filled with water and the temperature change associated with the gradual increase of moisture inside the wall was measured. This measurement lasted until the saturation which was the time when the wall has no more moisture to adopt. The second stage then examined the evolution of the temperature inside the wall during gradual desiccation until the time when the temperature inside the wall was uniform between all layers. © COPYRIGHT SPIE. Downloading of the abstract is permitted for personal use only.

Název v anglickém jazyce

Masonry moisture measurement using the distributed temperature sensing system

Popis výsledku anglicky

Distributed temperature sensing systems (DTS) are based on the principle of time-domain reflectometry where an optical fiber acts as a temperature sensor. DTS is capable of measuring the temperature along the optical fiber using the nonlinear phenomenon referred as Raman scattering. The biggest advantage of such sensing system is the use of an optical fiber itself as a sensor which gives the benefits of electromagnetic interference immunity, low sensor cost, measurement distances up to 10 kilometers and the safe use in flammable and corrosive environments. Fiber optic DTS can be therefore used in the environments and processes in which the application of conventional sensors is impossible. This article discusses the use of DTS for the moisture measurement in the masonry. In structures with built-in optical fiber, the immediate detection and location of moisture are possible. To perform the measurements an experimental brick wall has been built and between each wall layer the optical fiber was placed. The wall was built in stainless steel tub with a drain valve and was placed on a mobile trolley. The dimensions of the wall were 106 x 100 x 30 cm. The actual measurements were carried out in two stages. In the first, the tub was filled with water and the temperature change associated with the gradual increase of moisture inside the wall was measured. This measurement lasted until the saturation which was the time when the wall has no more moisture to adopt. The second stage then examined the evolution of the temperature inside the wall during gradual desiccation until the time when the temperature inside the wall was uniform between all layers. © COPYRIGHT SPIE. Downloading of the abstract is permitted for personal use only.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20201 - Electrical and electronic engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings of SPIE - The International Society for Optical Engineering. Volume 10208

ISBN

978-1-5106-0917-4

ISSN

0277-786X

e-ISSN

neuvedeno

Počet stran výsledku

7

Strana od-do

1-7

Název nakladatele

SPIE

Místo vydání

Bellingham

Místo konání akce

Anaheim

Datum konání akce

11. 4. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—