Vibration emission as a potential source of information for abrasive waterjet quality process control

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27350%2F12%3A86084473" target="_blank" >RIV/61989100:27350/12:86084473 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.1007/s00170-011-3715-6" target="_blank" >http://dx.doi.org/10.1007/s00170-011-3715-6</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s00170-011-3715-6" target="_blank" >10.1007/s00170-011-3715-6</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Vibration emission as a potential source of information for abrasive waterjet quality process control

Popis výsledku v původním jazyce

The paper deals with basic research of vibration generated at abrasive waterjet cutting of materials and their analysis of frequency spectrum in the plane cut. As an experimental material, stainless steel AISI 309 has been used. Experimentally controlledfactor involved in the experiment was abrasive mass flow rate with values ma= 250 and 400 g.min -1 at a constant traverse speed v = 100 mm.min-1. The vibrations were recorded during experimental cutting by sensors PCB IMI type 607A11 placed on experimental material along the cut at a distance of 50 mm from the cutting plane. Data collection was carried by NI PXI measurement system and frequency analyzer Microlog GX-S. Signal was evaluated by virtual instrument created in the object-programming environment LabView 8.5. Various sizes of amplitudes were observed depending on the distance of abrasive waterjet cutting process from the beginning of the cut. Two peaks of frequency bands have been also found: the first between 500 and 600 Hz a

Název v anglickém jazyce

Vibration emission as a potential source of information for abrasive waterjet quality process control

Popis výsledku anglicky

The paper deals with basic research of vibration generated at abrasive waterjet cutting of materials and their analysis of frequency spectrum in the plane cut. As an experimental material, stainless steel AISI 309 has been used. Experimentally controlledfactor involved in the experiment was abrasive mass flow rate with values ma= 250 and 400 g.min -1 at a constant traverse speed v = 100 mm.min-1. The vibrations were recorded during experimental cutting by sensors PCB IMI type 607A11 placed on experimental material along the cut at a distance of 50 mm from the cutting plane. Data collection was carried by NI PXI measurement system and frequency analyzer Microlog GX-S. Signal was evaluated by virtual instrument created in the object-programming environment LabView 8.5. Various sizes of amplitudes were observed depending on the distance of abrasive waterjet cutting process from the beginning of the cut. Two peaks of frequency bands have been also found: the first between 500 and 600 Hz a

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JR - Ostatní strojírenství

OECD FORD obor

—

Projekt

<a href="/cs/project/ED2.1.00%2F03.0082" target="_blank" >ED2.1.00/03.0082: Institut čistých technologií těžby a užití energetických surovin</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2012

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

The international journal of advanced manufacturing technology

ISSN

0268-3768

e-ISSN

—

Svazek periodika

61

Číslo periodika v rámci svazku

1-4

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

10

Strana od-do

285-294

Kód UT WoS článku

000305350900024

EID výsledku v databázi Scopus

—