Assessment of influence of structural parameters on mechanical characteristics of directional hypo-stoichiometric Ni3Al based alloys
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27360%2F09%3A00022091" target="_blank" >RIV/61989100:27360/09:00022091 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Assessment of influence of structural parameters on mechanical characteristics of directional hypo-stoichiometric Ni3Al based alloys
Popis výsledku v původním jazyce
Samples of Ni3Al based alloys with hypo-stoichiometric composition, i.e. 23 and 22 at.% of aluminium were used for testing of selected mechanical properties. The samples were not alloyed by any impure elements. They were first cast into the shape of bars, which were then crystallised by Bridgman?s method. The samples were inserted into corundum tubes with a specified apex angle. Short tensile bars were prepared by lathe-turning with length of 55 mm and diameter of central part of the bar 5 mm. These samples show unusually high conventional values of ductility till ultimate strength, while values of strength limit were partly reduced in the samples with 22 at. % of aluminium. All the samples prepared in this manner had orientated structure, which was formed by the phase Ni3Al, but they contain also two-phase areas formed by solidified solution of nickel (?) and Ni3Al (??), so called network structure ?/??.
Název v anglickém jazyce
Assessment of influence of structural parameters on mechanical characteristics of directional hypo-stoichiometric Ni3Al based alloys
Popis výsledku anglicky
Samples of Ni3Al based alloys with hypo-stoichiometric composition, i.e. 23 and 22 at.% of aluminium were used for testing of selected mechanical properties. The samples were not alloyed by any impure elements. They were first cast into the shape of bars, which were then crystallised by Bridgman?s method. The samples were inserted into corundum tubes with a specified apex angle. Short tensile bars were prepared by lathe-turning with length of 55 mm and diameter of central part of the bar 5 mm. These samples show unusually high conventional values of ductility till ultimate strength, while values of strength limit were partly reduced in the samples with 22 at. % of aluminium. All the samples prepared in this manner had orientated structure, which was formed by the phase Ni3Al, but they contain also two-phase areas formed by solidified solution of nickel (?) and Ni3Al (??), so called network structure ?/??.
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JG - Hutnictví, kovové materiály
OECD FORD obor
—
Návaznosti výsledku
Projekt
—
Návaznosti
Z - Vyzkumny zamer (s odkazem do CEZ)
Ostatní
Rok uplatnění
2009
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Hutnické listy
ISSN
0018-8069
e-ISSN
—
Svazek periodika
62
Číslo periodika v rámci svazku
6
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
5
Strana od-do
—
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—