Identification of Surface Quality of Plastic Electrodes after Blasting

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27360%2F13%3A86088666" target="_blank" >RIV/61989100:27360/13:86088666 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/DDF.334-335.71" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/DDF.334-335.71</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/DDF.334-335.71" target="_blank" >10.4028/www.scientific.net/DDF.334-335.71</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Identification of Surface Quality of Plastic Electrodes after Blasting

Popis výsledku v původním jazyce

Nowadays, plastics have become one of the most demanded materials, replacing the traditional ones such as metals. Therefore, many companies are concerned with the production of plastics, with their distribution and innovation development. Plastics have found utility in a wide range of applications, we use them every day. Measurement of surface roughness of plastic moldings produced by the injection molding process was carried out by a contact profilometer Mitutoyo Surftest SJ401. A reason for this measurement is to obtain information about surface roughness. For further technical adjustment is required to have higher surface roughness what helps to increase electrical conductivity of plastic moldings. This involves determination of a ratio between Ra/Rz (the ratio between the arithmetic average of the roughness profile Ra and the average maximum height of the profile Rz) in order to satisfy customer demand for achieving better surface characteristics leading to an increase in electrica

Název v anglickém jazyce

Identification of Surface Quality of Plastic Electrodes after Blasting

Popis výsledku anglicky

Nowadays, plastics have become one of the most demanded materials, replacing the traditional ones such as metals. Therefore, many companies are concerned with the production of plastics, with their distribution and innovation development. Plastics have found utility in a wide range of applications, we use them every day. Measurement of surface roughness of plastic moldings produced by the injection molding process was carried out by a contact profilometer Mitutoyo Surftest SJ401. A reason for this measurement is to obtain information about surface roughness. For further technical adjustment is required to have higher surface roughness what helps to increase electrical conductivity of plastic moldings. This involves determination of a ratio between Ra/Rz (the ratio between the arithmetic average of the roughness profile Ra and the average maximum height of the profile Rz) in order to satisfy customer demand for achieving better surface characteristics leading to an increase in electrica

Druh

D - Stať ve sborníku

CEP obor

JR - Ostatní strojírenství

OECD FORD obor

—

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2013

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Defect and Diffusion Forum. Volume 334-335

ISBN

978-3-03785-662-8

ISSN

1012-0386

e-ISSN

—

Počet stran výsledku

6

Strana od-do

71-76

Název nakladatele

Trans Tech Publications

Místo vydání

Durnten-Zurich

Místo konání akce

Istanbul

Datum konání akce

25. 6. 2012

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000317868600013