TESTING OF ADHESIVE JOINTS DURING CURING AS A FUNCTION OF TEMPERATURE AND TIME

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27360%2F25%3A10260546" target="_blank" >RIV/61989100:27360/25:10260546 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.37904/metal.2025.5135" target="_blank" >https://doi.org/10.37904/metal.2025.5135</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.37904/metal.2025.5135" target="_blank" >10.37904/metal.2025.5135</a>

Jazyk výsledku

angličtina

Název v původním jazyce

TESTING OF ADHESIVE JOINTS DURING CURING AS A FUNCTION OF TEMPERATURE AND TIME

Popis výsledku v původním jazyce

This article focuses on the effect of curing temperature on the strength of adhesive joints used in vehicle prototypes. Testing the influence of curing temperature on the adhesive joint was carried out on samples of aluminum alloy EN AW 5754, with the adhesive surface prepared by abrasive blasting. Samples of aluminum alloy were bonded using three types of two-component adhesives. Two types of adhesive joints are addressed here. Firstly, adhesive joints cured at +20 °C for 168 hours, and secondly adhesive joints cured at +80 °C for 1 hour. The samples are tested using a tensile test, and the resulting data is plotted in graphs in the experimental section and compared. The achieved results of the experimental activity are discussed in the conclusion. © METAL 2025.All rights reserved.

Název v anglickém jazyce

TESTING OF ADHESIVE JOINTS DURING CURING AS A FUNCTION OF TEMPERATURE AND TIME

Popis výsledku anglicky

This article focuses on the effect of curing temperature on the strength of adhesive joints used in vehicle prototypes. Testing the influence of curing temperature on the adhesive joint was carried out on samples of aluminum alloy EN AW 5754, with the adhesive surface prepared by abrasive blasting. Samples of aluminum alloy were bonded using three types of two-component adhesives. Two types of adhesive joints are addressed here. Firstly, adhesive joints cured at +20 °C for 168 hours, and secondly adhesive joints cured at +80 °C for 1 hour. The samples are tested using a tensile test, and the resulting data is plotted in graphs in the experimental section and compared. The achieved results of the experimental activity are discussed in the conclusion. © METAL 2025.All rights reserved.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20500 - Materials engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

METAL 2025 : 34th International Conference on Metallurgy and Materials : conference proceedings : May 21 - 23, 2025, Orea Congress Hotel Brno, Czech Republic, EU

ISBN

978-80-88365-27-3

ISSN

2694-9296

e-ISSN

—

Počet stran výsledku

6

Strana od-do

309-314

Název nakladatele

Tanger

Místo vydání

Ostrava

Místo konání akce

Brno

Datum konání akce

21. 5. 2025

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—