Wear Analysis of Extracted Polyethylene Acetabular Cups Using a 3D Optical Scanner

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989592%3A15110%2F16%3A33163040" target="_blank" >RIV/61989592:15110/16:33163040 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216305:26210/16:PU119064 RIV/00098892:_____/17:N0000143

Výsledek na webu

<a href="http://dx.doi.org/10.1080/10402004.2016.1176286" target="_blank" >http://dx.doi.org/10.1080/10402004.2016.1176286</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1080/10402004.2016.1176286" target="_blank" >10.1080/10402004.2016.1176286</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Wear Analysis of Extracted Polyethylene Acetabular Cups Using a 3D Optical Scanner

Popis výsledku v původním jazyce

Wear analysis of total hip replacements (THRs) is considered one of the most relevant research areas helping to improve the longevity and overall design of THRs. The coordinate machine method (CMM) and Fourier profilometry are the most common methods for measuring THR wear. This article presents optical scanner digitalization as a new method for measuring the wear of polyethylene (PE) acetabular cups. The aim of this article is to explore the potential of this method for the PE wear measurements. Optical scans for the purposes of this study were produced using an ATOS Triple Scan 3D optical scanner. The optical scanner is efficient and it can measure a large number of points for polygonization and for further development of the preworn models. In this study, the scanner first generated point clouds on a sample of 13 retrieved ultra-high-molecular-weight polyethylene (UHMWPE) acetabular cups. Next, volumetric models of the cups were created by polygonizing the point clouds. Reverse engineering was used to develop models of the original acetabular cups using the geometry of the unworn parts of the retrieved cups. A comparison of the two models then showed the total volume of the PE debris. The optical scanning method was validated against the gravimetric method using three new acetabular cups that were worn out on a hip pendulum simulator. Validation shows that the optical scanning method is a valid method for wear analysis of the retrieved UHMWPE acetabular cups.

Název v anglickém jazyce

Wear Analysis of Extracted Polyethylene Acetabular Cups Using a 3D Optical Scanner

Popis výsledku anglicky

Wear analysis of total hip replacements (THRs) is considered one of the most relevant research areas helping to improve the longevity and overall design of THRs. The coordinate machine method (CMM) and Fourier profilometry are the most common methods for measuring THR wear. This article presents optical scanner digitalization as a new method for measuring the wear of polyethylene (PE) acetabular cups. The aim of this article is to explore the potential of this method for the PE wear measurements. Optical scans for the purposes of this study were produced using an ATOS Triple Scan 3D optical scanner. The optical scanner is efficient and it can measure a large number of points for polygonization and for further development of the preworn models. In this study, the scanner first generated point clouds on a sample of 13 retrieved ultra-high-molecular-weight polyethylene (UHMWPE) acetabular cups. Next, volumetric models of the cups were created by polygonizing the point clouds. Reverse engineering was used to develop models of the original acetabular cups using the geometry of the unworn parts of the retrieved cups. A comparison of the two models then showed the total volume of the PE debris. The optical scanning method was validated against the gravimetric method using three new acetabular cups that were worn out on a hip pendulum simulator. Validation shows that the optical scanning method is a valid method for wear analysis of the retrieved UHMWPE acetabular cups.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

FI - Traumatologie a ortopedie

OECD FORD obor

—

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Tribology Transactions

ISSN

1040-2004

e-ISSN

—

Svazek periodika

59

Číslo periodika v rámci svazku

AUG

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

11

Strana od-do

1-11

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—