Surface Monitoring of an MSW Landfill Based on Linear and Angular Measurements, TLS, and LIDAR UAV

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43210%2F23%3A43923183" target="_blank" >RIV/62156489:43210/23:43923183 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.3390/s23041847" target="_blank" >https://doi.org/10.3390/s23041847</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/s23041847" target="_blank" >10.3390/s23041847</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Surface Monitoring of an MSW Landfill Based on Linear and Angular Measurements, TLS, and LIDAR UAV

Popis výsledku v původním jazyce

Surface monitoring of landfills is crucial not only during their operation but also for later land restoration and development. Measurements concern environmental factors, such as leachate, migration of pollutants to water, biogas, and atmospheric emissions, and geotechnical factors, such as stability and subsidence. Landfill subsidence can be measured using modern surveying techniques. Modern measurement methods for landfill body displacement monitoring and their control after restoration and adaptation as recreational areas include terrestrial laser scanning (TLS), and scanning and low-altitude photogrammetric measurements from an unmanned aerial vehicle (UAV). The acquired measurement data in the form of 3D point clouds should be referenced to the local control network to enable a comprehensive analysis of data acquired using various techniques, including geotechnical sensors such as benchmarks, piezometers, and inclinometers. This study discusses the need for surface monitoring of municipal solid waste (MSW) landfills. A properly 3-D mapped landfill mass is the basis for ensuring the geotechnical safety of the restored landfill. Based on archival data and current measurements of the Radiowo landfill (Poland), this study compares the advantages and limitations of the following measurement techniques: linear and angular measurements, satellite measurements, TLS, and UAV scanning and photogrammetry, considering specific conditions of the location and vegetation of the landfill. Solutions for long-term monitoring were proposed, considering the cost and time resolution necessary for creating a differential model of landfill geometry changes.

Název v anglickém jazyce

Surface Monitoring of an MSW Landfill Based on Linear and Angular Measurements, TLS, and LIDAR UAV

Popis výsledku anglicky

Surface monitoring of landfills is crucial not only during their operation but also for later land restoration and development. Measurements concern environmental factors, such as leachate, migration of pollutants to water, biogas, and atmospheric emissions, and geotechnical factors, such as stability and subsidence. Landfill subsidence can be measured using modern surveying techniques. Modern measurement methods for landfill body displacement monitoring and their control after restoration and adaptation as recreational areas include terrestrial laser scanning (TLS), and scanning and low-altitude photogrammetric measurements from an unmanned aerial vehicle (UAV). The acquired measurement data in the form of 3D point clouds should be referenced to the local control network to enable a comprehensive analysis of data acquired using various techniques, including geotechnical sensors such as benchmarks, piezometers, and inclinometers. This study discusses the need for surface monitoring of municipal solid waste (MSW) landfills. A properly 3-D mapped landfill mass is the basis for ensuring the geotechnical safety of the restored landfill. Based on archival data and current measurements of the Radiowo landfill (Poland), this study compares the advantages and limitations of the following measurement techniques: linear and angular measurements, satellite measurements, TLS, and UAV scanning and photogrammetry, considering specific conditions of the location and vegetation of the landfill. Solutions for long-term monitoring were proposed, considering the cost and time resolution necessary for creating a differential model of landfill geometry changes.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10511 - Environmental sciences (social aspects to be 5.7)

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Sensors

ISSN

1424-8220

e-ISSN

1424-8220

Svazek periodika

23

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

16

Strana od-do

1847

Kód UT WoS článku

000939961100001

EID výsledku v databázi Scopus

2-s2.0-85148974705