Mechanical Properties of Knock-down Joints in Honeycomb Panels

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43410%2F13%3A00203329" target="_blank" >RIV/62156489:43410/13:00203329 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.ncsu.edu/bioresources/BioRes_08/BioRes_08_4_4873_Koreny_Mech_Prop_Knock-Down_Joints_Honeycomb_4213.pdf" target="_blank" >http://www.ncsu.edu/bioresources/BioRes_08/BioRes_08_4_4873_Koreny_Mech_Prop_Knock-Down_Joints_Honeycomb_4213.pdf</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Mechanical Properties of Knock-down Joints in Honeycomb Panels

Popis výsledku v původním jazyce

This study focuses on the use of demountable furniture joints in combination with 38-mm-thick honeycomb panels. These fittings were incorporated into L-shaped corner joints and then tested to determine their bending moment capacity. Overall, seven combinations of demountable fittings were tested. These groups of connectors consisted of solution non-glued, partly-glued connectors, and fully-glued connectors. All of the connectors were positioned in the test samples as they are commonly located in furniture construction. The highest capacities were obtained with glued connectors, followed by partly glued and then non-glued connectors. The difference in capacity between the inside and outside positions was insignificant for the non-glued and fully-glued connectors. A large difference between connectors in different positions was found for the partly glued connectors and for the second type of unglued connectors. The modes of failure were analyzed for each connector, and the possibilities

Název v anglickém jazyce

Mechanical Properties of Knock-down Joints in Honeycomb Panels

Popis výsledku anglicky

This study focuses on the use of demountable furniture joints in combination with 38-mm-thick honeycomb panels. These fittings were incorporated into L-shaped corner joints and then tested to determine their bending moment capacity. Overall, seven combinations of demountable fittings were tested. These groups of connectors consisted of solution non-glued, partly-glued connectors, and fully-glued connectors. All of the connectors were positioned in the test samples as they are commonly located in furniture construction. The highest capacities were obtained with glued connectors, followed by partly glued and then non-glued connectors. The difference in capacity between the inside and outside positions was insignificant for the non-glued and fully-glued connectors. A large difference between connectors in different positions was found for the partly glued connectors and for the second type of unglued connectors. The modes of failure were analyzed for each connector, and the possibilities

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JI - Kompositní materiály

OECD FORD obor

—

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2013

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

BioResources

ISSN

1930-2126

e-ISSN

—

Svazek periodika

8

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

10

Strana od-do

4873-4882

Kód UT WoS článku

328280700009

EID výsledku v databázi Scopus

—