Content of respirable and inhalable fractions in dust created while sawing beech wood and its modifications

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43410%2F15%3A43906562" target="_blank" >RIV/62156489:43410/15:43906562 - isvavai.cz</a>

Výsledek na webu

<a href="http://drewno-wood.pl/pobierz-196" target="_blank" >http://drewno-wood.pl/pobierz-196</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.12841/wood.1644-3985.096.11" target="_blank" >10.12841/wood.1644-3985.096.11</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Content of respirable and inhalable fractions in dust created while sawing beech wood and its modifications

Popis výsledku v původním jazyce

This paper presents the results of the granulometric analysis of sawdust, created during the sawing of modified and unmodified beech wood with a circular saw. The aim of this work was to analyze the effect of the treatment of beech wood (Fagus sylvaticaL.) on the content of respirable and inhalable particles in sawdust generated during the sawing process using a modern circular saw. Different methods of particle-size determination were used. The results obtained from the sieve analysis prove that the sawdust created during the cutting of DMDHEU was finer than the sawdust from native beech and other modified materials. It was also discovered that the dust created during the cutting of Bendywood was finer than when machining native beech and Lignamon. There was an increase in the share of fine fraction in the range of granularity x < 100 ?m at the expense of the fraction x = 0.25-1 mm. The properties of Lignamon are primarily based on the properties of raw wood material, therefore this

Název v anglickém jazyce

Content of respirable and inhalable fractions in dust created while sawing beech wood and its modifications

Popis výsledku anglicky

This paper presents the results of the granulometric analysis of sawdust, created during the sawing of modified and unmodified beech wood with a circular saw. The aim of this work was to analyze the effect of the treatment of beech wood (Fagus sylvaticaL.) on the content of respirable and inhalable particles in sawdust generated during the sawing process using a modern circular saw. Different methods of particle-size determination were used. The results obtained from the sieve analysis prove that the sawdust created during the cutting of DMDHEU was finer than the sawdust from native beech and other modified materials. It was also discovered that the dust created during the cutting of Bendywood was finer than when machining native beech and Lignamon. There was an increase in the share of fine fraction in the range of granularity x < 100 ?m at the expense of the fraction x = 0.25-1 mm. The properties of Lignamon are primarily based on the properties of raw wood material, therefore this

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JQ - Strojní zařízení a nástroje

OECD FORD obor

—

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Drewno

ISSN

1644-3985

e-ISSN

—

Svazek periodika

58

Číslo periodika v rámci svazku

194

Stát vydavatele periodika

PL - Polská republika

Počet stran výsledku

12

Strana od-do

135-146

Kód UT WoS článku

000366320800011

EID výsledku v databázi Scopus

—