Comparative study on the bending moment capacity and stiffness of innovative and traditional furniture corner joints

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62156489%3A43410%2F25%3A43925603" target="_blank" >RIV/62156489:43410/25:43925603 - isvavai.cz</a>

Výsledek na webu

<a href="https://doi.org/10.1080/17480272.2024.2391068" target="_blank" >https://doi.org/10.1080/17480272.2024.2391068</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1080/17480272.2024.2391068" target="_blank" >10.1080/17480272.2024.2391068</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Comparative study on the bending moment capacity and stiffness of innovative and traditional furniture corner joints

Popis výsledku v původním jazyce

This study compares the bending moment capacity under compression and bending moment capacity under tension values of eight selected structural furniture joints. Specimens (type L) with a dimension of 150 x 150 x 366 mm were made from three-layer, 18 mm thick particleboard. The corner joints were tested in angular bending in compression and tension. Both classic and new joining elements (plastic cam, zinc cam, one-part plastic connector, screw cam, plastic connector with euroscrew, and birch dowel pre-glued) for the simple assembly of furniture were used in the study. Cam joints with wooden dowels can withstand high stress. There are only minimal differences between joints made of plastic or zinc cams with dowels. If birch dowels with an adhesive coating are added to the plastic joint from sample with plastic connector with euroscrew, this joint will reach 126% higher values in angular bending tests - compressive stress.

Název v anglickém jazyce

Comparative study on the bending moment capacity and stiffness of innovative and traditional furniture corner joints

Popis výsledku anglicky

This study compares the bending moment capacity under compression and bending moment capacity under tension values of eight selected structural furniture joints. Specimens (type L) with a dimension of 150 x 150 x 366 mm were made from three-layer, 18 mm thick particleboard. The corner joints were tested in angular bending in compression and tension. Both classic and new joining elements (plastic cam, zinc cam, one-part plastic connector, screw cam, plastic connector with euroscrew, and birch dowel pre-glued) for the simple assembly of furniture were used in the study. Cam joints with wooden dowels can withstand high stress. There are only minimal differences between joints made of plastic or zinc cams with dowels. If birch dowels with an adhesive coating are added to the plastic joint from sample with plastic connector with euroscrew, this joint will reach 126% higher values in angular bending tests - compressive stress.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10700 - Other natural sciences

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Wood Material Science and Engineering

ISSN

1748-0272

e-ISSN

1748-0280

Svazek periodika

20

Číslo periodika v rámci svazku

6

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

9

Strana od-do

1227-1235

Kód UT WoS článku

001299334000001

EID výsledku v databázi Scopus

2-s2.0-85202542876