CoMn Catalysts Derived from Hydrotalcite-Like Precursors for Direct Conversion of Syngas to Fuel Range Hydrocarbons

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F62243136%3A_____%2F20%3AN0000042" target="_blank" >RIV/62243136:_____/20:N0000042 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/2073-4344/10/8/813/htm" target="_blank" >https://www.mdpi.com/2073-4344/10/8/813/htm</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/catal10080813" target="_blank" >10.3390/catal10080813</a>

Jazyk výsledku

angličtina

Název v původním jazyce

CoMn Catalysts Derived from Hydrotalcite-Like Precursors for Direct Conversion of Syngas to Fuel Range Hydrocarbons

Popis výsledku v původním jazyce

Two different groups of CoMn catalysts derived from hydrotalcite-like precursors were prepared through the co-precipitation method, and their performance in the direct production of gasoline and jet fuel range hydrocarbons through Fischer–Tropsch (FT) synthesis was evaluated in a batch autoclave reactor at 240 °C and 7 MPa and H2/CO of 2. The physicochemical properties of the prepared catalysts were investigated and characterized using different characterization techniques. Catalyst performance was significantly affected by the catalyst preparation method. The crystalline phase of the catalyst prepared using KOH contained Co3O4 and some Co2MnO4.5 spinels, with a lower reducibility and catalytic activity than cobalt oxide. The available cobalt active sites are responsible for the chain growth, and the accessible acid sites are responsible for the cracking and isomerization. The catalysts prepared using KOH + K2CO3 mixture as a precipitant agent exhibited a high selectivity of 51–61% for gasoline (C5–C10) and 30–50% for jet fuel (C8–C16) range hydrocarbons compared with catalysts precipitated by KOH. The CoMn-HTC-III catalyst with the highest number of available acid sites showed the highest selectivity to C5–C10 hydrocarbons, which demonstrates that a high Bronsted acidity leads to the high degree of cracking of FT products. The CO conversion did not significantly change, and it was around 35–39% for all catalysts. Owing to the poor activity in the water-gas shift reaction, CO2 formation was less than 2% in all the catalysts.

Název v anglickém jazyce

CoMn Catalysts Derived from Hydrotalcite-Like Precursors for Direct Conversion of Syngas to Fuel Range Hydrocarbons

Popis výsledku anglicky

Two different groups of CoMn catalysts derived from hydrotalcite-like precursors were prepared through the co-precipitation method, and their performance in the direct production of gasoline and jet fuel range hydrocarbons through Fischer–Tropsch (FT) synthesis was evaluated in a batch autoclave reactor at 240 °C and 7 MPa and H2/CO of 2. The physicochemical properties of the prepared catalysts were investigated and characterized using different characterization techniques. Catalyst performance was significantly affected by the catalyst preparation method. The crystalline phase of the catalyst prepared using KOH contained Co3O4 and some Co2MnO4.5 spinels, with a lower reducibility and catalytic activity than cobalt oxide. The available cobalt active sites are responsible for the chain growth, and the accessible acid sites are responsible for the cracking and isomerization. The catalysts prepared using KOH + K2CO3 mixture as a precipitant agent exhibited a high selectivity of 51–61% for gasoline (C5–C10) and 30–50% for jet fuel (C8–C16) range hydrocarbons compared with catalysts precipitated by KOH. The CoMn-HTC-III catalyst with the highest number of available acid sites showed the highest selectivity to C5–C10 hydrocarbons, which demonstrates that a high Bronsted acidity leads to the high degree of cracking of FT products. The CO conversion did not significantly change, and it was around 35–39% for all catalysts. Owing to the poor activity in the water-gas shift reaction, CO2 formation was less than 2% in all the catalysts.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20400 - Chemical engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Catalysts

ISSN

2073-4344

e-ISSN

—

Svazek periodika

10

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

17

Strana od-do

1-17

Kód UT WoS článku

000564681500001

EID výsledku v databázi Scopus

—