Nanostructured TiNb coating improves the bioactivity of 3D printed PEEK
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F67985823%3A_____%2F22%3A00565698" target="_blank" >RIV/67985823:_____/22:00565698 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/68407700:21220/22:00360736 RIV/00216208:11320/22:10456772
Výsledek na webu
<a href="https://doi.org/10.1016/j.matdes.2022.111312" target="_blank" >https://doi.org/10.1016/j.matdes.2022.111312</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.matdes.2022.111312" target="_blank" >10.1016/j.matdes.2022.111312</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Nanostructured TiNb coating improves the bioactivity of 3D printed PEEK
Popis výsledku v původním jazyce
Polyetheretherketone (PEEK) has mechanical properties suitable for the manufacturing of osseointegration implants. However, its biological properties can be significantly improved by surface modification. In this work, the macroscopic surface topography was obtained by 3D printing and then the 3D printed surface was coated with a TiNb layer. The coating made it possible to apply anodic oxidation, by which a surface with defined nanoscale topography was obtained. Thus, a material with a gradient surface topography and suitable chemical composition was prepared. The properties of the surface were analyzed using optical and scanning electron microscopy. The chemical composition was then evaluated by photoelectron spectroscopy. The roughness, the wettability, and the wear resistance of the surface were observed. The adhesion of the coating and the oxide layer was evaluated. The biological activity of samples was analyzed by seeding them with human osteoblast-like Saos-2 cells. The cell adhesion, proliferation, metabolic activity and viability was observed and was statistically evaluated. After this, the functionality of this surface modification was tested by applying it to an implant with a real geometry. The main conclusions show that the nanostructured TiNb layer on 3D printed PEEK significantly improves biological activity.
Název v anglickém jazyce
Nanostructured TiNb coating improves the bioactivity of 3D printed PEEK
Popis výsledku anglicky
Polyetheretherketone (PEEK) has mechanical properties suitable for the manufacturing of osseointegration implants. However, its biological properties can be significantly improved by surface modification. In this work, the macroscopic surface topography was obtained by 3D printing and then the 3D printed surface was coated with a TiNb layer. The coating made it possible to apply anodic oxidation, by which a surface with defined nanoscale topography was obtained. Thus, a material with a gradient surface topography and suitable chemical composition was prepared. The properties of the surface were analyzed using optical and scanning electron microscopy. The chemical composition was then evaluated by photoelectron spectroscopy. The roughness, the wettability, and the wear resistance of the surface were observed. The adhesion of the coating and the oxide layer was evaluated. The biological activity of samples was analyzed by seeding them with human osteoblast-like Saos-2 cells. The cell adhesion, proliferation, metabolic activity and viability was observed and was statistically evaluated. After this, the functionality of this surface modification was tested by applying it to an implant with a real geometry. The main conclusions show that the nanostructured TiNb layer on 3D printed PEEK significantly improves biological activity.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
30211 - Orthopaedics
Návaznosti výsledku
Projekt
<a href="/cs/project/GA20-01570S" target="_blank" >GA20-01570S: Zlepšení osteointegrace kostních implantátů jejich pokrytím feroelektrickými vrstvami</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2022
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Materials and Design
ISSN
0264-1275
e-ISSN
1873-4197
Svazek periodika
224
Číslo periodika v rámci svazku
Dec
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
15
Strana od-do
111312
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-85140979414