Reliability of the Chevron-notch technique for fracture toughness determination in glass.
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081723%3A_____%2F03%3A07033010" target="_blank" >RIV/68081723:_____/03:07033010 - isvavai.cz</a>
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Reliability of the Chevron-notch technique for fracture toughness determination in glass.
Popis výsledku v původním jazyce
The applicability of the chevron-notch (CN) three-point bending test for determining the fracture toughness (KIc) of borosilicate glass was studied. As-received specimens with straight sharp notch were also tested in three-point bending for comparison purposes. It was found that both chevron and straight notched specimen geometries were equally suitable for the determination of fracture toughness in terms of average values and data variability according to Weibull and Student's t -statistics. Further testing with CN geometry showed that annealing of specimens at a temperature (550 8C) higher than the glass transformation temperature led to a lower value of KIc. The difference in mean fracture toughness values (0.75 and 0.64 MPam1/2 before and after annealing, respectively), was ascribed to the different level of compressive residual stresses in the samples. The Student's t -test was applied to confirm the statistical significance of the different KIc values measured. These results demo
Název v anglickém jazyce
Reliability of the Chevron-notch technique for fracture toughness determination in glass.
Popis výsledku anglicky
The applicability of the chevron-notch (CN) three-point bending test for determining the fracture toughness (KIc) of borosilicate glass was studied. As-received specimens with straight sharp notch were also tested in three-point bending for comparison purposes. It was found that both chevron and straight notched specimen geometries were equally suitable for the determination of fracture toughness in terms of average values and data variability according to Weibull and Student's t -statistics. Further testing with CN geometry showed that annealing of specimens at a temperature (550 8C) higher than the glass transformation temperature led to a lower value of KIc. The difference in mean fracture toughness values (0.75 and 0.64 MPam1/2 before and after annealing, respectively), was ascribed to the different level of compressive residual stresses in the samples. The Student's t -test was applied to confirm the statistical significance of the different KIc values measured. These results demo
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JH - Keramika, žáruvzdorné materiály a skla
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/IAA2041003" target="_blank" >IAA2041003: Mikromechanika křehkého lomu a statistické modely</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>Z - Vyzkumny zamer (s odkazem do CEZ)
Ostatní
Rok uplatnění
2003
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Materials Science and Engineering A. Elsevier
ISSN
0921-5093
e-ISSN
—
Svazek periodika
347
Číslo periodika v rámci svazku
1/2
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
7
Strana od-do
102-108
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—