Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081723%3A_____%2F21%3A00576256" target="_blank" >RIV/68081723:_____/21:00576256 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.37904/metal.2021.4147" target="_blank" >http://dx.doi.org/10.37904/metal.2021.4147</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.37904/metal.2021.4147" target="_blank" >10.37904/metal.2021.4147</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel

Popis výsledku v původním jazyce

The objective of the study is to evaluate the effects of severe plastic deformation (SPD) and annealing on creep behaviour of advanced tungsten modified creep-resistant 9 % Cr martensitic P92 steel. The as-received P92 steel was deformed by high-pressure torsion (HTP), high-pressure sliding (HPS) and rotary swaging (RS) at room temperature prior creep testing. These SPD methods imposed significantly different equivalent plastic strain in the range from 1 up to 20. Constant load creep tests in tension were performed in an argon atmosphere at 873 K and applied stress ranging from 50 to 200 MPa. The microstructure and phase composition of P92 steel were studied using a scanning electron microscope Tescan Lyra 3 and a transmission electron microscope Jeol 2100F. The results show that under the same creep loading conditions the HPT and HPS-processed P92 steel exhibited significantly faster minimum creep rates, creep fracture strain and the decrease in the value of the stress exponent of the creep rate in comparison with as-received P92 steel. However, it was revealed that the RS-processed specimens exhibited one order of magnitude lower minimum creep rate and lower ductility compared to commercial P92 steel. The creep curves for the HPT and HPS-processed states exhibited a pronounced minimum of strain rate. The pronounced minimum of strain rate disappeared when these states were annealed at 923K/500h before application of creep loading. The microstructure changes occurring during creep and different creep behaviour between as-received and deformed states are discussed.

Název v anglickém jazyce

Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel

Popis výsledku anglicky

The objective of the study is to evaluate the effects of severe plastic deformation (SPD) and annealing on creep behaviour of advanced tungsten modified creep-resistant 9 % Cr martensitic P92 steel. The as-received P92 steel was deformed by high-pressure torsion (HTP), high-pressure sliding (HPS) and rotary swaging (RS) at room temperature prior creep testing. These SPD methods imposed significantly different equivalent plastic strain in the range from 1 up to 20. Constant load creep tests in tension were performed in an argon atmosphere at 873 K and applied stress ranging from 50 to 200 MPa. The microstructure and phase composition of P92 steel were studied using a scanning electron microscope Tescan Lyra 3 and a transmission electron microscope Jeol 2100F. The results show that under the same creep loading conditions the HPT and HPS-processed P92 steel exhibited significantly faster minimum creep rates, creep fracture strain and the decrease in the value of the stress exponent of the creep rate in comparison with as-received P92 steel. However, it was revealed that the RS-processed specimens exhibited one order of magnitude lower minimum creep rate and lower ductility compared to commercial P92 steel. The creep curves for the HPT and HPS-processed states exhibited a pronounced minimum of strain rate. The pronounced minimum of strain rate disappeared when these states were annealed at 923K/500h before application of creep loading. The microstructure changes occurring during creep and different creep behaviour between as-received and deformed states are discussed.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/GA19-18725S" target="_blank" >GA19-18725S: Vliv mikrostruktury na creepové mechanismy v pokročilých žárupevných ocelích</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

METAL 2021. 30th Anniversary International Conference on Metallurgy and Materials. Conference proceedings

ISBN

978-80-87294-99-4

ISSN

2694-9296

e-ISSN

—

Počet stran výsledku

6

Strana od-do

429-434

Název nakladatele

TANGER

Místo vydání

Ostrava

Místo konání akce

Brno

Datum konání akce

26. 5. 2021

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

001242770500067