The Effect of Hardness and Surface Roughness of Elastomer on Friction Between Shoe Soles and Particle-Contaminated Floors

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081723%3A_____%2F25%3A00637771" target="_blank" >RIV/68081723:_____/25:00637771 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216305:26210/26:0198509

Výsledek na webu

<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:001532590000001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:001532590000001</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s11249-025-02046-4" target="_blank" >10.1007/s11249-025-02046-4</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The Effect of Hardness and Surface Roughness of Elastomer on Friction Between Shoe Soles and Particle-Contaminated Floors

Popis výsledku v původním jazyce

Nearly one third of workplace injuries results from slip- and trip-induced falls. Solid particles are among the most common floor contaminants in both occupational and outdoor environments, reducing shoe-floor friction and increasing slip risk. This study investigates how rubber hardness and surface roughness affect the frictional behaviour of shoe soles on smooth, particle-contaminated floors. Coefficient of friction (COF) measurements and post-test surface wear analyses were conducted using nitrile rubbers with hardness between 57.9 and 84.0 ShA and varied surface roughness. Samples were slid against smooth epoxy flooring in a pin-on-plate test simulating the heel-strike phase of walking. The floor was either clean or uniformly covered with corundum particles (40-50 mu m, 120-140 mu m, or 280-315 mu m). On clean floors, increasing rubber hardness and roughness significantly decreased COF (p < 0.0001) due to reduced real contact area. Under contaminated conditions, softer and rougher rubbers yielded higher COF values (p < 0.0001). Higher COF correlated with greater floor wear, showing long scratches and grooves, suggesting slip occurs mainly at the particle-floor interface. Rubber hardness and surface roughness primarily influence the strength of the particle-elastomer interface, greater particle-elastomer strength suppresses particle rolling and thereby leads to an increase in COF. These findings indicate that, on particle-contaminated smooth floors, slip resistance is governed more by particle-floor interactions than by rubber adhesion. Increasing outsole roughness and reducing hardness can help mitigate the adverse effects of particle rolling within the contact area and improve the frictional performance of the outsole.

Název v anglickém jazyce

The Effect of Hardness and Surface Roughness of Elastomer on Friction Between Shoe Soles and Particle-Contaminated Floors

Popis výsledku anglicky

Nearly one third of workplace injuries results from slip- and trip-induced falls. Solid particles are among the most common floor contaminants in both occupational and outdoor environments, reducing shoe-floor friction and increasing slip risk. This study investigates how rubber hardness and surface roughness affect the frictional behaviour of shoe soles on smooth, particle-contaminated floors. Coefficient of friction (COF) measurements and post-test surface wear analyses were conducted using nitrile rubbers with hardness between 57.9 and 84.0 ShA and varied surface roughness. Samples were slid against smooth epoxy flooring in a pin-on-plate test simulating the heel-strike phase of walking. The floor was either clean or uniformly covered with corundum particles (40-50 mu m, 120-140 mu m, or 280-315 mu m). On clean floors, increasing rubber hardness and roughness significantly decreased COF (p < 0.0001) due to reduced real contact area. Under contaminated conditions, softer and rougher rubbers yielded higher COF values (p < 0.0001). Higher COF correlated with greater floor wear, showing long scratches and grooves, suggesting slip occurs mainly at the particle-floor interface. Rubber hardness and surface roughness primarily influence the strength of the particle-elastomer interface, greater particle-elastomer strength suppresses particle rolling and thereby leads to an increase in COF. These findings indicate that, on particle-contaminated smooth floors, slip resistance is governed more by particle-floor interactions than by rubber adhesion. Increasing outsole roughness and reducing hardness can help mitigate the adverse effects of particle rolling within the contact area and improve the frictional performance of the outsole.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/EH22_008%2F0004634" target="_blank" >EH22_008/0004634: Strojní inženýrství biologických a bioinspirovaných systémů</a><br>

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2025

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Tribology Letters

ISSN

1023-8883

e-ISSN

1573-2711

Svazek periodika

73

Číslo periodika v rámci svazku

3

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

15

Strana od-do

106

Kód UT WoS článku

001532590000001

EID výsledku v databázi Scopus

2-s2.0-105011152288