Numerical modeling and Schlieren visualization of the gas-assisted laser cutting under various operating stagnation pressures
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68081731%3A_____%2F20%3A00519170" target="_blank" >RIV/68081731:_____/20:00519170 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.sciencedirect.com/science/article/abs/pii/S0017931019339663" target="_blank" >https://www.sciencedirect.com/science/article/abs/pii/S0017931019339663</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.ijheatmasstransfer.2019.118965" target="_blank" >10.1016/j.ijheatmasstransfer.2019.118965</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Numerical modeling and Schlieren visualization of the gas-assisted laser cutting under various operating stagnation pressures
Popis výsledku v původním jazyce
The uniformity of the exit jet pattern in high pressure gas-assisted laser cutting represents the main feature in order to achieve high cutting quality and capability. Therefore, the effect of both inlet stagnation pressure and nozzle geometry on the behavior of the exit jet has been investigated in this research. Quasi 1-D gas dynamics theory has been used to calculate the exact-design operating conditions for three different supersonic nozzles that were fabricated by means of Wire Electrical Discharge Machining. The jet flow through these nozzles has been numerically modeled and experimentally checked, using Schlieren visualization, under exact-design, over-expansion and under-expansion operating conditions coming to a good numerical-experimental agreement in terms of flow structure. As main result, the exit jet was found to preserve its uniform distribution with parallel boundaries and low divergence under the exact-design operating condition, differently to what observed for the others two conditions, especially for nozzle with small divergence angle.
Název v anglickém jazyce
Numerical modeling and Schlieren visualization of the gas-assisted laser cutting under various operating stagnation pressures
Popis výsledku anglicky
The uniformity of the exit jet pattern in high pressure gas-assisted laser cutting represents the main feature in order to achieve high cutting quality and capability. Therefore, the effect of both inlet stagnation pressure and nozzle geometry on the behavior of the exit jet has been investigated in this research. Quasi 1-D gas dynamics theory has been used to calculate the exact-design operating conditions for three different supersonic nozzles that were fabricated by means of Wire Electrical Discharge Machining. The jet flow through these nozzles has been numerically modeled and experimentally checked, using Schlieren visualization, under exact-design, over-expansion and under-expansion operating conditions coming to a good numerical-experimental agreement in terms of flow structure. As main result, the exit jet was found to preserve its uniform distribution with parallel boundaries and low divergence under the exact-design operating condition, differently to what observed for the others two conditions, especially for nozzle with small divergence angle.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
10305 - Fluids and plasma physics (including surface physics)
Návaznosti výsledku
Projekt
—
Návaznosti
I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2020
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
International Journal of Heat and Mass Transfer
ISSN
0017-9310
e-ISSN
—
Svazek periodika
147
Číslo periodika v rámci svazku
FEB
Stát vydavatele periodika
US - Spojené státy americké
Počet stran výsledku
11
Strana od-do
118965
Kód UT WoS článku
000505101200084
EID výsledku v databázi Scopus
2-s2.0-85075537702