An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68145535%3A_____%2F15%3A00447734" target="_blank" >RIV/68145535:_____/15:00447734 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.inderscience.com/jhome.php?jcode=ijsurfse#issue" target="_blank" >http://www.inderscience.com/jhome.php?jcode=ijsurfse#issue</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1504/IJSURFSE.2015.072069" target="_blank" >10.1504/IJSURFSE.2015.072069</a>

Jazyk výsledku

angličtina

Název v původním jazyce

An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions

Popis výsledku v původním jazyce

The paper presents the results of the research into the impact of anti-wear added to emulsion mist on the geometrical state of the machined surface of stainless steel after turning. In the research, the following machining conditions were compared: dry machining and cooling with compressed air, emulsion mist, emulsion mist + Crodafos O4A-LQ-(MH) and emulsion mist + Crodafos EHA-LQ-(MH). In the first stage, the influence of modifiers on roughness parameters of the machined surface were established. The aim of the second stage was to submit the machined material to microroentgenospectral analysis. The presence of chemical elements on the machined material surface for the aforementioned conditions of machining was analysed. Research results indicate thatthe application of cooling with emulsion mist with modifiers reduces the roughness parameters of the machined material even up to 80%. Adequately selected conditions of forming emulsion mist forms border layer, beneficially influencing th

Název v anglickém jazyce

An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions

Popis výsledku anglicky

The paper presents the results of the research into the impact of anti-wear added to emulsion mist on the geometrical state of the machined surface of stainless steel after turning. In the research, the following machining conditions were compared: dry machining and cooling with compressed air, emulsion mist, emulsion mist + Crodafos O4A-LQ-(MH) and emulsion mist + Crodafos EHA-LQ-(MH). In the first stage, the influence of modifiers on roughness parameters of the machined surface were established. The aim of the second stage was to submit the machined material to microroentgenospectral analysis. The presence of chemical elements on the machined material surface for the aforementioned conditions of machining was analysed. Research results indicate thatthe application of cooling with emulsion mist with modifiers reduces the roughness parameters of the machined material even up to 80%. Adequately selected conditions of forming emulsion mist forms border layer, beneficially influencing th

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JQ - Strojní zařízení a nástroje

OECD FORD obor

—

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

International Journal of Surface Science and Engineering

ISSN

1749-785X

e-ISSN

—

Svazek periodika

9

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

14

Strana od-do

452-465

Kód UT WoS článku

000364815300007

EID výsledku v databázi Scopus

—