Comparison of non-destructive sensing methods on surface created by waterjet technology

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68145535%3A_____%2F19%3A00494135" target="_blank" >RIV/68145535:_____/19:00494135 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/chapter/10.1007/978-3-319-99353-9_13" target="_blank" >https://link.springer.com/chapter/10.1007/978-3-319-99353-9_13</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/978-3-319-99353-9_13" target="_blank" >10.1007/978-3-319-99353-9_13</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Comparison of non-destructive sensing methods on surface created by waterjet technology

Popis výsledku v původním jazyce

The article is a response to the lack of information, especially in the area of non-destructive techniques suitable for wide practical application. The article deals with evaluation of the disintegrated material volume removed from the samples by a water jet. The study presents a quantified disintegrated material volume by means of an optical profilometer MicroProf FRT, a digital microscope VHX-5100 and X-ray computed micro-tomograph XT H 225 ST. Based on a comparison of measured data, it is possible to state that the methods of optical profilometer and a digital microscope give us very close volume values. While the values of the volume of removed material analysed by X-Ray μ-CT reach higher its values. After detailed analysis of the individual tomographic cross-sections in area of kerf surface it can be concluded that complex morphology of this surface can explain differences in the results. There are visible some re-entrant features like an overhangs and undercuts at the surface created by high pressure water jet.

Název v anglickém jazyce

Comparison of non-destructive sensing methods on surface created by waterjet technology

Popis výsledku anglicky

The article is a response to the lack of information, especially in the area of non-destructive techniques suitable for wide practical application. The article deals with evaluation of the disintegrated material volume removed from the samples by a water jet. The study presents a quantified disintegrated material volume by means of an optical profilometer MicroProf FRT, a digital microscope VHX-5100 and X-ray computed micro-tomograph XT H 225 ST. Based on a comparison of measured data, it is possible to state that the methods of optical profilometer and a digital microscope give us very close volume values. While the values of the volume of removed material analysed by X-Ray μ-CT reach higher its values. After detailed analysis of the individual tomographic cross-sections in area of kerf surface it can be concluded that complex morphology of this surface can explain differences in the results. There are visible some re-entrant features like an overhangs and undercuts at the surface created by high pressure water jet.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

<a href="/cs/project/LO1406" target="_blank" >LO1406: Institut čistých technologií těžby a užití energetických surovin - Projekt udržitelnosti</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Advances in Manufacturing Engineering and Materials

ISBN

978-3-319-99353-9

ISSN

2195-4356

e-ISSN

—

Počet stran výsledku

10

Strana od-do

114-123

Název nakladatele

Springer Nature Switzerland AG 2019

Místo vydání

Basel

Místo konání akce

Nový Smokovec

Datum konání akce

18. 6. 2018

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000462541600013