Effect of abrasive water jet machining on the geometry of shapes in selected tool steels
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68145535%3A_____%2F21%3A00533239" target="_blank" >RIV/68145535:_____/21:00533239 - isvavai.cz</a>
Výsledek na webu
<a href="https://link.springer.com/chapter/10.1007/978-3-030-53491-2_5" target="_blank" >https://link.springer.com/chapter/10.1007/978-3-030-53491-2_5</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1007/978-3-030-53491-2_5" target="_blank" >10.1007/978-3-030-53491-2_5</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Effect of abrasive water jet machining on the geometry of shapes in selected tool steels
Popis výsledku v původním jazyce
The presented article is focused on the abrasive water jet machining of tool steel material. Selected tool steels Uddeholm Dievar and Böhler K110 were machined and final pockets were evaluated based on the side angle of the pocket. Sequentially were created pockets with increasing depth from 1 to 5 mm for both materials. Evaluation of pocket angle is crucial factor for determination of machining allowance for finishing cuts. Also metallography analysis for both materials was created for observation of removal process and for detection of cracks produced during abrasive water jet machining. In terms of corrosion of presented tool steels can be stated that due to higher number of alloying elements is corrosion on machined surface acceptable for further processing of created shapes. Obtained results can extend application possibilities of AWJ milling for rough machining of tool steels, especially for thin-walled components with reduction of induced residual stresses and deformations of shapes.
Název v anglickém jazyce
Effect of abrasive water jet machining on the geometry of shapes in selected tool steels
Popis výsledku anglicky
The presented article is focused on the abrasive water jet machining of tool steel material. Selected tool steels Uddeholm Dievar and Böhler K110 were machined and final pockets were evaluated based on the side angle of the pocket. Sequentially were created pockets with increasing depth from 1 to 5 mm for both materials. Evaluation of pocket angle is crucial factor for determination of machining allowance for finishing cuts. Also metallography analysis for both materials was created for observation of removal process and for detection of cracks produced during abrasive water jet machining. In terms of corrosion of presented tool steels can be stated that due to higher number of alloying elements is corrosion on machined surface acceptable for further processing of created shapes. Obtained results can extend application possibilities of AWJ milling for rough machining of tool steels, especially for thin-walled components with reduction of induced residual stresses and deformations of shapes.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2021
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
Advances in Water Jetting
ISBN
978-3-030-53490-5
ISSN
2195-4356
e-ISSN
2195-4364
Počet stran výsledku
7
Strana od-do
49-55
Název nakladatele
Springer
Místo vydání
Cham
Místo konání akce
Čeladná
Datum konání akce
20. 11. 2019
Typ akce podle státní příslušnosti
WRD - Celosvětová akce
Kód UT WoS článku
—