Evaluation of the Depth and Width of Cuts after Controlled-Depth Abrasive Water Jet Machining Using Low Pressure

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F68145535%3A_____%2F23%3A00604602" target="_blank" >RIV/68145535:_____/23:00604602 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/16/24/7532" target="_blank" >https://www.mdpi.com/1996-1944/16/24/7532</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma16247532" target="_blank" >10.3390/ma16247532</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Evaluation of the Depth and Width of Cuts after Controlled-Depth Abrasive Water Jet Machining Using Low Pressure

Popis výsledku v původním jazyce

The presented paper is focused on the evaluation of material removal during machining via an abrasive water jet with a controlled depth of cut. In the introductory parts of the work, a theoretical analysis of water jet technology and an analysis of the current state of the problem are presented. The experimental part of the work is devoted to testing the effects of technological parameters on material removal from the point of view of the maximum erosion depth and volume loss of material during machining with a low water pressure of 50 MPa. The tested material was a Ti 6Al 4V titanium alloy. The experiments were carried out by changing the traverse speed of the cutting head, the mass flow of the abrasive and the angle of inclination of the cutting head, according to the DoE 33 experiment plan. The obtained values were evaluated using the method of variance (ANOVA) and regression analysis. Furthermore, the values of the width of the erosion track and the maximum and minimum erosion effects for both tested materials were evaluated.

Název v anglickém jazyce

Evaluation of the Depth and Width of Cuts after Controlled-Depth Abrasive Water Jet Machining Using Low Pressure

Popis výsledku anglicky

The presented paper is focused on the evaluation of material removal during machining via an abrasive water jet with a controlled depth of cut. In the introductory parts of the work, a theoretical analysis of water jet technology and an analysis of the current state of the problem are presented. The experimental part of the work is devoted to testing the effects of technological parameters on material removal from the point of view of the maximum erosion depth and volume loss of material during machining with a low water pressure of 50 MPa. The tested material was a Ti 6Al 4V titanium alloy. The experiments were carried out by changing the traverse speed of the cutting head, the mass flow of the abrasive and the angle of inclination of the cutting head, according to the DoE 33 experiment plan. The obtained values were evaluated using the method of variance (ANOVA) and regression analysis. Furthermore, the values of the width of the erosion track and the maximum and minimum erosion effects for both tested materials were evaluated.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

1996-1944

Svazek periodika

16

Číslo periodika v rámci svazku

24

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

17

Strana od-do

7532

Kód UT WoS článku

001131295000001

EID výsledku v databázi Scopus

2-s2.0-85180616820